Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

power steering arm travel 630 JD ?


 
Post new topic    
View previous topic :: View next topic  
Author Message
fumblefarmer98
Regular


Joined: 01 Jun 2014
Posts: 77


Report to Moderator

PostPosted: Mon May 11, 2020 3:31 pm    Post subject: power steering arm travel 630 JD ? Reply to specific post Reply with quote

Anyone know how much travel there should be in the steering arm on the 630 jd power steering valve ? Got steering valve off turning the steering wheel right to left it seems as though that arm total travel would be less than a eighth of an inch . Seems too little to operate the steering spool enough ? Thanks ,Marty
 
Back to top
View user's profile
wore out
Long Time User


Joined: 01 Oct 2019
Posts: 1208


Report to Moderator

PostPosted: Mon May 11, 2020 8:32 pm    Post subject: Re: power steering arm travel 630 JD ? Reply to specific post Reply with quote

CVPost-fumblefarmer98 wrote:
(quoted from post at 16:31:53 05/11/20) Anyone know how much travel there should be in the steering arm on the 630 jd power steering valve ? Got steering valve off turning the steering wheel right to left it seems as though that arm total travel would be less than a eighth of an inch . Seems too little to operate the steering spool enough ? Thanks ,Marty


Are you having problems with the power steering?

To answer you question, the valve doesn't need to be moved much to do it's job, but I don't have an actual measurement/number for you.

When the actuating "helix" gets worn, chipped, or damaged that affects valve actuating "travel" and how the steering works, that's for sure.

I don't see any "travel spec" in the Two Cylinder Power Steering Manual, either

Here's what it DOES say:



HTH!
 
Back to top
View user's profile
Rich Duane
Long Time User


Joined: 04 Dec 2007
Posts: 537


Report to Moderator

PostPosted: Tue May 12, 2020 5:17 am    Post subject: Re: power steering arm travel 630 JD ? Reply to specific post Reply with quote

The valve arm full movement is about .020 either way. Most of the problem is the worm bearings are out of adjustment not
allowing the valve enough movement. If you have the JD SM 2050 Two Cylinder Power Steering Manual it will instruct you on
correcting this problem.
 
Back to top
View user's profile
fumblefarmer98
Regular


Joined: 01 Jun 2014
Posts: 77


Report to Moderator

PostPosted: Tue May 12, 2020 9:15 am    Post subject: Re: power steering arm travel 630 JD ? Reply to specific post Reply with quote

Thank you both for the help . Seems so small amount . Did nt want to go farther without asking someone . Makes quite a leaning job . I do hve the 630 manual,the 2050 manual and 630 parts book .Still a chalenge and someone with hands on experience still a big help . Thanks
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters