Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Allis B front crank seal, felt and rubber


 
Post new topic    
View previous topic :: View next topic  
Author Message
Luke9
New User


Joined: 17 Jun 2019
Posts: 7


Report to Moderator

PostPosted: Mon May 18, 2020 9:20 am    Post subject: Allis B front crank seal, felt and rubber Reply to specific post Reply with quote

My YT rebuild kit came with two front seals. One is only a rubber lip seal, and fits fairly loosely. I assume that is intended for use with a speedi-sleeve to cover the spiral grooves. The other is wider and has both the felt seal and a rubber lip in the same seal. The direction of the garter seems to indicate the rubber should go inboard, but that would still leave it on the spirals. Flipping it around with the felt inside and the rubber outwards lays out better, but the garter faces out now.

I was just expecting a felt only seal with the kit. Anybody put this type of seal in, and what direction did you install it?
 
Back to top
View user's profile
RalphWD45
Tractor Expert


Joined: 05 Jan 2008
Posts: 1812
Location: Roy, Wa.

Report to Moderator

PostPosted: Fri May 22, 2020 3:54 pm    Post subject: Re: Allis B front crank seal, felt and rubber Reply to specific post Reply with quote

Luke 9, Move up three posts ,to 1939 B post, and read it. I think it will answer your question! You need the speedi sleeve!
 
Back to top
View user's profile
Luke9
New User


Joined: 17 Jun 2019
Posts: 7


Report to Moderator

PostPosted: Wed May 27, 2020 11:12 am    Post subject: Re: Allis B front crank seal, felt and rubber Reply to specific post Reply with quote

Thanks, Ralph. That is the conclusion I came to also and ordered a sleeve. After looking at the two seals again, the original has a 1 15/16" O.D. and is the same as the lip seal supplied with the kit. The other seal in the kit is 2" OD, so the timing cover would need bored out to accomodate it. The sleeve looked like the cheaper/easier option.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters