Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

I will jump in as a lot of dc questions


 
Post new topic    
View previous topic :: View next topic  
Author Message
dc in illinois
Regular


Joined: 23 Mar 2011
Posts: 127
Location: Northern Il.

Report to Moderator

PostPosted: Mon Jun 29, 2020 9:10 pm    Post subject: I will jump in as a lot of dc questions Reply to specific post Reply with quote

Don Livingston/rusty acres is the person who seams to be in the know about this .I know that he has a reconditioned dc intake and exhaust manifold for a dc tractor. what I am asking what does it take to recondition one other than the obvious trueing of the mating surfaces. I have heard a little talk about the ferials for the intake and exhaust .how do you know when the go bad? my dc ran really good 2 years ago then while moving snow heard a loud pop and after looking hard I found that I had lost a valve lock/keeper on number 4 exhaust . I let it sit in the shed till I found replacment parts. I have adjusted the valves a few times. but here a grueling in the intake as it is pulling air in will try to start but just pops of for a few revolutions before it dies. carb is getting gas. mag is sparking. just need some advice where I should look next as have fuel, have spark, and is in time per the book. the only thing I haven't tried is pull starting. also I know the compression is good

Thanks for any ideas in advance
Bob
 
Back to top
View user's profile
olgentdc
Tractor Guru


Joined: 10 Aug 2008
Posts: 4077


Report to Moderator

PostPosted: Tue Jun 30, 2020 4:15 am    Post subject: Re: I will jump in as a lot of dc questions Reply to specific post Reply with quote

" grueling " Gurgeling sounds like water in the works ....Have you cleaned the air filter ,.. try st arting with the breather off
 
Back to top
View user's profile
dc in illinois
Regular


Joined: 23 Mar 2011
Posts: 127
Location: Northern Il.

Report to Moderator

PostPosted: Tue Jun 30, 2020 5:58 am    Post subject: Re: I will jump in as a lot of dc questions Reply to specific post Reply with quote

thanks for your reply i will try that and see what we get

bob
 
Back to top
View user's profile
rustred
Tractor Guru


Joined: 01 Jul 2009
Posts: 32361


Report to Moderator

PostPosted: Tue Jun 30, 2020 7:18 am    Post subject: Re: I will jump in as a lot of dc questions Reply to specific post Reply with quote

you said it run good till you lost a valve keeper. then you adjusted the valves a few times. did you adjust each cyl. on TDC on the COMPRESSION stroke to .018? and what is the compression? a person needs actual setting spec's. diagnosing a problem . not questioning your work but need to eliminate stuff. have a hard time to believe its the manifold when it ran good before as you said. plus is the firing order correct...? 1342 clockwise. popping is caused by valves and timing.
 
Back to top
View user's profile
dc in illinois
Regular


Joined: 23 Mar 2011
Posts: 127
Location: Northern Il.

Report to Moderator

PostPosted: Tue Jun 30, 2020 4:41 pm    Post subject: Re: I will jump in as a lot of dc questions Reply to specific post Reply with quote

thanks wil let you know as going to reset valves and check firing order

Bob
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters