Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Removing a centrifugal clutch


 
Post new topic    
View previous topic :: View next topic  
Author Message
Catchb52
New User


Joined: 19 Jul 2020
Posts: 2


Report to Moderator

PostPosted: Sun Jul 19, 2020 1:06 pm    Post subject: Removing a centrifugal clutch Reply to specific post Reply with quote

I have a Wisconsin single cylinder motor that is used on an ingersoll Rand packmaster compactor. I need to remove the centrifugal clutch off the shaft.

Outside pulley was held on with a C ring and it pulled off. Inner clutch does not have a set screw that I can find. The backing plate is too thin to use a 3 jaw puller on.

I can't get a bearing puller behind it enough to grab.

Any thoughts on what might work to pull it off?[/img:2a84e7e5fd]
 
Back to top
View user's profile
teddy52food
Tractor Guru


Joined: 05 Mar 2006
Posts: 9748


Report to Moderator

PostPosted: Mon Jul 20, 2020 5:52 pm    Post subject: Re: Removing a centrifugal clutch Reply to specific post Reply with quote

Is it on a taper? Get a pry behind it & hit the shaft with a brass hammer.
 
Back to top
View user's profile
Catchb52
New User


Joined: 19 Jul 2020
Posts: 2


Report to Moderator

PostPosted: Mon Jul 20, 2020 11:23 pm    Post subject: Re: Removing a centrifugal clutch Reply to specific post Reply with quote

CVPost-teddy52food wrote:
(quoted from post at 18:52:04 07/20/20) Is it on a taper? Get a pry behind it & hit the shaft with a brass hammer.


Not that I can tell. Looks like a regular shalt. There is a my on it, so I am assuming it was pressed on. I have never seen one on a regular shalt without a set screw.

I am going to build a plate I can get behind the clutch shaft and then heat the shaft.

K will let the group know how it works.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Stationary Engines All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters