Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

445 water pump removal


 
Post new topic    
View previous topic :: View next topic  
Author Message
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6431


Report to Moderator

PostPosted: Thu Jul 30, 2020 8:08 pm    Post subject: 445 water pump removal Reply to specific post Reply with quote

Im assuming the fan needs to be removed to take the water pump out? Are there nuts on the inside of the pulley or are they
stationary in the pulley? The I&T book says to remove the air cleaner and take it out that side of the tractor.
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2781


Report to Moderator

PostPosted: Fri Jul 31, 2020 4:23 am    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Just 4 bolts hold fan to pump.
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6431


Report to Moderator

PostPosted: Fri Jul 31, 2020 6:53 am    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Yes, 4 bolts but Im wondering on the inside of the pulley. The one I have looks like there are square nuts in it.
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2781


Report to Moderator

PostPosted: Fri Jul 31, 2020 8:35 am    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Just checked in shop manual. Shows taking out with fan still attached. Not a lot of room. Never seen nuts on inside. Maybe studs were coming loose. Same pump as on all Jetstars.Have changed changed several. Rebuilds are only way to go unless you want to fight with seal.
 
Back to top
View user's profile
Cliff Nelson
Tractor Expert


Joined: 26 Mar 2009
Posts: 1561


Report to Moderator

PostPosted: Fri Jul 31, 2020 4:49 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

The square nuts are welded to the pulley.
 
Back to top
View user's profile
ChrisQ
Regular


Joined: 05 Nov 2012
Posts: 358
Location: Jordan, MN

Report to Moderator

PostPosted: Fri Jul 31, 2020 6:57 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Might want to just put bandages on your knuckles before you start. Seems I always end up bleeding changing a water pump on them.
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6431


Report to Moderator

PostPosted: Fri Jul 31, 2020 8:38 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

LOL I know what you mean
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6431


Report to Moderator

PostPosted: Fri Jul 31, 2020 8:38 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

That is what I figured and was hoping. Thank you
 
Back to top
View user's profile
T.R.K.
Tractor Expert


Joined: 14 Apr 2013
Posts: 2347


Report to Moderator

PostPosted: Mon Aug 03, 2020 8:07 am    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Its been a while, but I think you might want to take the water pump out with the plate it attaches to. You probably want to renew the o-rings on the water tube while its apart. If the tube is 'iffy' you might want to replace it too.
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6431


Report to Moderator

PostPosted: Wed Aug 05, 2020 8:59 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Sounds like a good plan. Not a lot of room on them with the plate in the way.
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6431


Report to Moderator

PostPosted: Thu Aug 06, 2020 8:45 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Got the pump out but need to disassemble it. Which direction does the bearing and shaft get pressed out. Need to get the hub and pulley off for the other pump. Hopefully the wire lock will come out...maybe lol.
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2781


Report to Moderator

PostPosted: Fri Aug 07, 2020 2:41 pm    Post subject: Re: 445 water pump removal Reply to specific post Reply with quote

Every 206 I rebuild get new water tubes, O rings and waterpump. Will come back to bite you every time.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters