Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

need 32 rims for a red face U


 
Post new topic    
View previous topic :: View next topic  
Author Message
eas
Regular


Joined: 24 Sep 2007
Posts: 50


Report to Moderator

PostPosted: Mon Sep 14, 2020 2:29 pm    Post subject: need 32 rims for a red face U Reply to specific post Reply with quote

need 32" rims for a red face U ?????
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2807


Report to Moderator

PostPosted: Mon Sep 14, 2020 2:54 pm    Post subject: Re: need 32 rims for a red face U Reply to specific post Reply with quote

Same rim as UDLX and GT. I have one extra. Won't be easy to find and tires same if not worse. Only used until 1939. You could change hub to a 38,36 or a 30. Also could use a 34 or 36 rim and shim inside.
 
Back to top
View user's profile
kgreg
Regular


Joined: 01 Sep 2013
Posts: 52


Report to Moderator

PostPosted: Mon Sep 14, 2020 5:00 pm    Post subject: Re: need 32 rims for a red face U Reply to specific post Reply with quote

I've got one 32 inch rim from a red nose uts I parted out. It has been cut and widened. I'm located in central mn.
 
Back to top
View user's profile
eas
Regular


Joined: 24 Sep 2007
Posts: 50


Report to Moderator

PostPosted: Tue Sep 15, 2020 8:17 am    Post subject: Re: need 32 rims for a red face U Reply to specific post Reply with quote

kgreg what has it been widen too?? 12" ???
 
Back to top
View user's profile
eas
Regular


Joined: 24 Sep 2007
Posts: 50


Report to Moderator

PostPosted: Tue Sep 15, 2020 8:19 am    Post subject: Re: need 32 rims for a red face U Reply to specific post Reply with quote

what do want for it ? what width is it ???
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2807


Report to Moderator

PostPosted: Tue Sep 15, 2020 4:11 pm    Post subject: Re: need 32 rims for a red face U Reply to specific post Reply with quote

Original tire 12.75 Rim is 10 inch. Going to be tough to find a good 80 year old rim. Am in MB. Best to find some 38 inch hubs and change out.
 
Back to top
View user's profile
kgreg
Regular


Joined: 01 Sep 2013
Posts: 52


Report to Moderator

PostPosted: Wed Sep 16, 2020 4:08 pm    Post subject: Re: need 32 rims for a red face U Reply to specific post Reply with quote

I had time to get a measurement and yes it is 12 inches wide. Has some rust but might work for you.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters