Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Tight filter canister


 
Post new topic    
View previous topic :: View next topic  
Author Message
4020_guy
Regular


Joined: 05 Jul 2015
Posts: 133


Report to Moderator

PostPosted: Tue Sep 15, 2020 5:57 pm    Post subject: Tight filter canister Reply to specific post Reply with quote

Went to change the hydraulic filter on the 770. Drained the canister and then tried to unscrew the bottom, one 1/1/4 wrench, two 1/1/4 wrenchs , tapping all around with hammer, tapping all around with bigger hammer, tapping all around with big hammer with a 6 pound hammer held up to the opposite side, and using a big cold chisel and one of the a fore mentioned hammers. Nothing. Maybe air gun next? Would like to use the 770 the next few days so I'll wait til then. Any other ideas? Thanks.......Ron
 
Back to top
View user's profile
J Hamilton
Long Time User


Joined: 07 Apr 2020
Posts: 837


Report to Moderator

PostPosted: Tue Sep 15, 2020 6:19 pm    Post subject: Re: Tight filter canister Reply to specific post Reply with quote

I had to use an air gun to get mine broke loose on an 1170
 
Back to top
View user's profile
Joe (Wa)
Tractor Expert


Joined: 01 Jan 1999
Posts: 2840


Report to Moderator

PostPosted: Tue Sep 15, 2020 7:45 pm    Post subject: Re: Tight filter canister Reply to specific post Reply with quote

A good impact will rattle just about any thing loose, go both ways with it until you get some movement. Wrench is probably best to work it the rest of the way off, work it back & forth to clean the threads to keep them from galling.

Joe
 
Back to top
View user's profile
Don Rudolph
Tractor Guru


Joined: 29 Aug 2010
Posts: 3754


Report to Moderator

PostPosted: Tue Sep 15, 2020 7:49 pm    Post subject: Re: Tight filter canister Reply to specific post Reply with quote

They can be a real bear. We tried tapping with a hammer and it split right open. Salvage yard would not attempt to open the replacement. YOYO-you're on your own, they said. Our local machinist/welder lightly heated it and turned it loose with a pipe wrench and a four foot long pipe. This one didn't break. Good Luck! Don
 
Back to top
View user's profile
fred goodrich
Tractor Expert


Joined: 16 Dec 2007
Posts: 1631


Report to Moderator

PostPosted: Wed Sep 16, 2020 3:25 am    Post subject: Re: Tight filter canister Reply to specific post Reply with quote

they can be a real bear. don't leave the relief valve in the old filter or you will get a big surprise, I have shipped those valves all over the country.
 
Back to top
View user's profile
dwag
Long Time User


Joined: 13 Jul 2004
Posts: 1317


Report to Moderator

PostPosted: Wed Sep 16, 2020 6:47 am    Post subject: Re: Tight filter canister Reply to specific post Reply with quote

After U get it off with a 3/4" impact and perhaps a little heat, make sure threads are clean and cap will screw on freely by hand.
 
Back to top
View user's profile
451 CUBES
Regular


Joined: 28 Apr 2016
Posts: 256
Location: South of the Mississippi

Report to Moderator

PostPosted: Wed Sep 16, 2020 4:53 pm    Post subject: Re: Tight filter canister Reply to specific post Reply with quote

What everyone else said...... two weeks after battling a very stuck one I had it blew apart. Machine had been sitting busted 20 years so it was a bit tight. With good luck you will have the bypass valve in the bottom of your filter like Fred Said . They don’t need to be wailed on either when reinstalling, just snug.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters