Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Intake and exhaust manifold


 
Post new topic    
View previous topic :: View next topic  
Author Message
Brad500
New User


Joined: 14 Oct 2020
Posts: 9


Report to Moderator

PostPosted: Fri Oct 16, 2020 6:16 am    Post subject: Intake and exhaust manifold Reply to specific post Reply with quote

I was beginning to take off the carburetor last night but noticed where the carburetor attaches to the intake there appears to be a separation between the intake pipe and where the carburetor attaches. It doesn't look like it is cracked but very clean as if someone sawed through it. Is it supposed to be this way? I would think this would allow air to get it from the outside and the carburetor to set to run to rich. I have looked an the manifolds offered as replacements and they appear to made differently. Will a replacement manifold fit with no modifications needed? Thanks in advance.



 
Back to top
View user's profile
J.Wondergem
Tractor Guru


Joined: 05 Mar 2009
Posts: 5869


Report to Moderator

PostPosted: Fri Oct 16, 2020 6:27 am    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote


I can't see it, but it doesn't sound right. Can you get a light to shine on it better when taking the picture?
 
Back to top
View user's profile
Brad500
New User


Joined: 14 Oct 2020
Posts: 9


Report to Moderator

PostPosted: Fri Oct 16, 2020 6:57 am    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote

It is right below the plug on the intake. I will try to take a better photo tonight.
 
Back to top
View user's profile
Jim in rush co
Long Time User


Joined: 12 May 2009
Posts: 1449


Report to Moderator

PostPosted: Fri Oct 16, 2020 1:45 pm    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote

I had my TO35 running today and thought of your manifold post so I grabbed a couple of pictures. Are these what you are talking about? Made that way to take the high heat of the exhaust and the cool of the intake at the same time.



 
Back to top
View user's profile
Brad500
New User


Joined: 14 Oct 2020
Posts: 9


Report to Moderator

PostPosted: Fri Oct 16, 2020 1:54 pm    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote

CVPost-Jim in Rush co wrote:
(quoted from post at 14:45:31 10/16/20) I had my TO35 running today and thought of your manifold post so I grabbed a couple of pictures. Are these what you are talking about? Made that way to take the high heat of the exhaust and the cool of the intake at the same time.
<img src="/cvphotos/cvphoto59616.jpg">

<img src="/cvphotos/cvphoto59617.jpg">


No right below the vacuum plug. The carburetor is below that and attached to the the intake part of the manifold. Just above the flange where the carburetor is attached is the separation You can see it in the photo.
 
Back to top
View user's profile
J.Wondergem
Tractor Guru


Joined: 05 Mar 2009
Posts: 5869


Report to Moderator

PostPosted: Sat Oct 17, 2020 1:17 pm    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote


I think I see maybe where your talking about. Kind of looks like a flange or something in the casting a inch or two below the vacuum plug?
 
Back to top
View user's profile
J.Wondergem
Tractor Guru


Joined: 05 Mar 2009
Posts: 5869


Report to Moderator

PostPosted: Sat Oct 17, 2020 1:27 pm    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote


Another thought, you could spray some WD40 or something on it while it's idling and see if it speeds up.
 
Back to top
View user's profile
Brad500
New User


Joined: 14 Oct 2020
Posts: 9


Report to Moderator

PostPosted: Sat Oct 17, 2020 4:49 pm    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote

Yes that’s it took off the carb and it appears it just
one solid piece maybe left over from manufacturers.
Just appears to be two pieced
 
Back to top
View user's profile
J.Wondergem
Tractor Guru


Joined: 05 Mar 2009
Posts: 5869


Report to Moderator

PostPosted: Sun Oct 18, 2020 9:13 am    Post subject: Re: Intake and exhaust manifold Reply to specific post Reply with quote


Glad to hear that.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters