Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Master Cylinder repair.


 
Post new topic    
View previous topic :: View next topic  
Author Message
rlp in Co.
Tractor Expert


Joined: 17 May 2010
Posts: 2151


Report to Moderator

PostPosted: Sat Nov 21, 2020 12:51 pm    Post subject: Master Cylinder repair. Reply to specific post Reply with quote

What is the order that these parts go in? There is a thick rubber washer in the kit that wasn't in the old master cylinder. It is a quart inch thick.There was a brass washer in the master cylinder that's not in the new kit. Where would it go or should I leave it out? Which way does the spring go?



 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 35407
Location: St. Cloud, MN

Report to Moderator

PostPosted: Sat Nov 21, 2020 3:08 pm    Post subject: Re: Master Cylinder repair. Reply to specific post Reply with quote

First in is a residual pressure check valve seal ring. (round Oring right side above the spring seat) next is the Check/spring seat, (silver thingy bottom right in your image). It is installed with the spring seat Dome surface pointing toward the spring. Next is the spring (end with no attachment in first, reversed from picture), next is the primary cup Plain rubber, no hole. Primary cup facing away from pushrod end of piston. Next is the Piston spool with push rod cup pointing rearward. (the piston has a new secondary cup installed facing away from the rod end as shown. Next is the snap ring collar and snap ring, then boot and push rod. Push rod link must be adjusted so piston has returned all the way to the snap ring, then a tiny bit looser to assure it does. (Maybe .025" slop). Jim
 
Back to top
View user's profile
rlp in Co.
Tractor Expert


Joined: 17 May 2010
Posts: 2151


Report to Moderator

PostPosted: Sat Nov 21, 2020 4:02 pm    Post subject: Re: Master Cylinder repair. Reply to specific post Reply with quote

Thanks a lot! I think I got it together right the first time for a change!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters