Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

changed PTO shaft in the 850


 
Post new topic    
View previous topic :: View next topic  
Author Message
steve in ok
Regular


Joined: 15 Aug 2008
Posts: 196


Report to Moderator

PostPosted: Wed Jan 13, 2021 6:01 am    Post subject: changed PTO shaft in the 850 Reply to specific post Reply with quote

When I changed the PTO shaft the old one came right out but I had to tap the new one in. Not hard to go in. Just concerned I may have hurt something in the trans. It seems to operate good as far as engaging and disengaging. What do you think?
 
Back to top
View user's profile
grandpa Love
Tractor Guru


Joined: 26 May 2016
Posts: 9330


Report to Moderator

PostPosted: Wed Jan 13, 2021 6:05 am    Post subject: Re: changed PTO shaft in the 850 Reply to specific post Reply with quote

Should be fine. I've changed 3-4 on my
Fords. Most needed a little tap. Maybe
because they ain't wore out?
 
Back to top
View user's profile
steve in ok
Regular


Joined: 15 Aug 2008
Posts: 196


Report to Moderator

PostPosted: Wed Jan 13, 2021 6:20 am    Post subject: Re: changed PTO shaft in the 850 Reply to specific post Reply with quote

Thank you sir, I just wanted a little reassurance I guess. Sure like seeing pictures and videos of your herd of Fords still working.
 
Back to top
View user's profile
sotxbill
Tractor Guru


Joined: 14 Jun 2003
Posts: 6878


Report to Moderator

PostPosted: Wed Jan 13, 2021 6:31 am    Post subject: Re: changed PTO shaft in the 850 Reply to specific post Reply with quote

I just pulled and reinstalled two last week.. Both had to be pulled with a bit of force and reinstalled with the same force. Seals were replace and reinstalled.

Had to use some long screwdrivers to wedge in between, to pull them out...

and tap a hammer to put them back. Both shafts showed to be true and no twist in the splines.

I have pulled some with a some "twist" in them with very long pry bars and a lot of hammer work. Someone probably hit a log or big rock with a shredder to twist the pto shafts.
 
Back to top
View user's profile
steve in ok
Regular


Joined: 15 Aug 2008
Posts: 196


Report to Moderator

PostPosted: Wed Jan 13, 2021 10:45 am    Post subject: Re: changed PTO shaft in the 850 Reply to specific post Reply with quote

That's good to know. I feel better about the way mine installed. Thanks
 
Back to top
View user's profile
riveroadrat
Tractor Expert


Joined: 26 Nov 2013
Posts: 1771


Report to Moderator

PostPosted: Sat Jan 16, 2021 5:53 am    Post subject: Re: changed PTO shaft in the 850 Reply to specific post Reply with quote

If someone hammered on the forward end when working on it usually. A little filing on the splines and they slip right in.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters