Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

CASE 310/300 GAS GOVERNOR, DWELL


 
Post new topic    
View previous topic :: View next topic  
Author Message
markputtkammer
New User


Joined: 13 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Wed Jan 13, 2021 7:23 am    Post subject: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

Just having a bad time tuning. put new needle and seat in and it stopped the gas from flowing while sitting, but now can't just get in and start it without starting fluid. Governor goes wide open when at start. Looking for linkage for it because wire goes from the handle to the linkage, but the parts that go around the motor seem to be all there but loose. Maybe the spring is the issue?? Wish someone was old school near Indy and could set the points, dwell, carb because I am not familiar with how a governor works, I have a good knowledge of things, just can't figure this out. No matter how I adjust the carb I can't get it right. The carb was a problem in the first place, but could get it started and worked fairly well. Replaced the points, the carb I rebuilt and now just can't control the rpms or start without starting fluid. Any advice would be appreciated.
 
Back to top
View user's profile
markputtkammer
New User


Joined: 13 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Wed Jan 13, 2021 8:42 am    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

Very Happy
 
Back to top
View user's profile
tomturkey
Tractor Expert


Joined: 21 Jul 2010
Posts: 2956


Report to Moderator

PostPosted: Wed Jan 13, 2021 9:39 am    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

I'd quit using that starting fluid. It is really hard on the pistons and rings. Try using carb cleaner instead. A bit less
explosive. I could be wrong on this, maybe carb cleaner is bad also. good luck gobble
 
Back to top
View user's profile
Tgrasher
Long Time User


Joined: 19 Dec 2019
Posts: 743


Report to Moderator

PostPosted: Wed Jan 13, 2021 2:08 pm    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

Sounds like you might want to check compression, if it's below 100 lbs you will have starting issues. A battery that's not up to par won't start a low compression engine as it doesn't spin it over fast enough to build compression. Try pulling in 4th gear to start and see how it runs, the starting fluid will cause the motor to race. I have a 300 with 85 lbs and it's a booger to start but once it warms up, it runs good.
 
Back to top
View user's profile
markputtkammer
New User


Joined: 13 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Thu Jan 14, 2021 5:34 am    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

New battery, didn't have a problem before starting. I don't think after 15 min of running that starting fluid would still make it have the governor make the carb arm move all the way forward. I can seem to control the governor or throttle because of either the carb or distributor, but admit I have wire to the control and a spring that I don't even know should be there or not by the carb.
 
Back to top
View user's profile
markputtkammer
New User


Joined: 13 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Thu Jan 14, 2021 7:09 am    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

talked to a guy who said I might need a rebuilt governor and some are just bolted on, don't know if mine are, got the manual from YT, and it is real helpful, but didn't mention governor in the trouble shooting as I can see. I need the shaft, it is missing, but seemed to work okay before, not perfect but still!
 
Back to top
View user's profile
Tgrasher
Long Time User


Joined: 19 Dec 2019
Posts: 743


Report to Moderator

PostPosted: Thu Jan 14, 2021 7:52 am    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

Here is what your linkage should look like. Seems (going back over 20 yrs) like I had a surging/reving problem that I fixed by putting the correct spring
on.



 
Back to top
View user's profile
markputtkammer
New User


Joined: 13 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Thu Jan 14, 2021 11:40 am    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

yes, but where to find the spring?
 
Back to top
View user's profile
Tgrasher
Long Time User


Joined: 19 Dec 2019
Posts: 743


Report to Moderator

PostPosted: Thu Jan 14, 2021 1:03 pm    Post subject: Re: CASE 310/300 GAS GOVERNOR, DWELL Reply to specific post Reply with quote

John Saeli - 315-585-9826. He knows his stuff/parts and will save you a lot of headaches and in the final result, money.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters