Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Collar


 
Post new topic    
View previous topic :: View next topic  
Author Message
bfullmer
Regular


Joined: 17 Dec 2011
Posts: 399


Report to Moderator

PostPosted: Wed Jan 13, 2021 12:52 pm    Post subject: Collar Reply to specific post Reply with quote

Have a 2 inch shaft going thru a bracket and I need
a collar to weld on to secure shaft with roll pin or
bolt no luck finding collar - what do you call them
and where can you buy them
 
Back to top
View user's profile
Bob Bancroft
Tractor Guru


Joined: 05 Mar 2009
Posts: 9438
Location: Aurora NY

Report to Moderator

PostPosted: Wed Jan 13, 2021 2:45 pm    Post subject: Re: Collar Reply to specific post Reply with quote

I have bought collars with a set screw at McMaster Carr.
 
Back to top
View user's profile
neverfear
Long Time User


Joined: 02 May 2010
Posts: 523


Report to Moderator

PostPosted: Sun Jan 17, 2021 5:06 am    Post subject: Re: Collar Reply to specific post Reply with quote

MSC has them.

https://www.mscdirect.com/product/details/35463827
 
Back to top
View user's profile
Jim.ME
Tractor Guru


Joined: 02 Mar 2018
Posts: 3757


Report to Moderator

PostPosted: Sun Jan 17, 2021 5:52 am    Post subject: Re: Collar Reply to specific post Reply with quote


Did you find what you were looking for yet?

Are you looking for a shaft collar or a weld on pin boss? A shaft collar normally locks (with set screws or clamping action) to the shaft. A pin boss welds to the base frame with a pin holding the shaft in it using a cross pin, like where the pins go through a loader bucket. If you are making weld on pin bosses a machine shop may have drawn over mandrel tubing, or similar in stock the size you want, that can be cut to the length you need. You might have to ream it out a bit for your fit and drill your own cross pin holes, or have them make the pieces you want.

Here is one outfit that sells DOM stock by the foot.
https://mysteelyard.com/index.php?cPath=40&page=3&osCsid=8a265fb1f7c258ef5d52e16e4388a0b1
 
Back to top
View user's profile
bfullmer
Regular


Joined: 17 Dec 2011
Posts: 399


Report to Moderator

PostPosted: Sun Jan 17, 2021 11:10 am    Post subject: Re: Collar Reply to specific post Reply with quote

Thanks for your reply never heard it called a pin
boss - I ended up using a piece of pipe / that DOM
tubing is expensive I only needed 4 inches for two
pieces
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters