Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Allis Chalmers Plow model question


 
Post new topic    
View previous topic :: View next topic  
Author Message
Dutchman1968
New User


Joined: 26 Sep 2019
Posts: 10


Report to Moderator

PostPosted: Sun Apr 18, 2021 4:51 am    Post subject: Allis Chalmers Plow model question Reply to specific post Reply with quote

Hello All,

I just purchased this plow at an auction to do some light plowing. Does anyone know what model of plow this is and what era it was made? Are they any good or light duty?

Thanks,

Dutch









 
Back to top
View user's profile
Aaron SEIA
Tractor Expert


Joined: 16 Dec 2003
Posts: 2528
Location: SE Iowa

Report to Moderator

PostPosted: Mon Apr 19, 2021 3:07 am    Post subject: Re: Allis Chalmers Plow model question Reply to specific post Reply with quote

I've gotta say that doesn't look AC to me. Parts of it does, but that tail wheel setup is something I've never seen before.
AaronSEIA
 
Back to top
View user's profile
DrAllis
Tractor Expert


Joined: 18 Jan 2015
Posts: 1586


Report to Moderator

PostPosted: Mon Apr 19, 2021 3:22 am    Post subject: Re: Allis Chalmers Plow model question Reply to specific post Reply with quote

50-series 3-point hitch plow with an optional tail wheel that I've never seen before. Must have been for a D-10/D-12.
 
Back to top
View user's profile
BonaparteSouth
Regular


Joined: 26 Jan 2019
Posts: 69


Report to Moderator

PostPosted: Mon Apr 19, 2021 5:00 am    Post subject: Re: Allis Chalmers Plow model question Reply to specific post Reply with quote

doesn't look AC to me. mostly pieces from junk pile and late night booze crew welding shop !! lol one of a kind
 
Back to top
View user's profile
4wdtom
Tractor Expert


Joined: 03 Oct 2014
Posts: 2188


Report to Moderator

PostPosted: Mon Apr 19, 2021 5:15 am    Post subject: Re: Allis Chalmers Plow model question Reply to specific post Reply with quote

I am no expert on AC plows but it does look to me like the frame (horizontal parts and the vertical stub beam that extends down to the plow bottoms, and the gusset plate that braces the stub beam) and details of construction is AC. The lower bolt in the gusset plate is referred to in the parts list for my WD no. 54 Two Way Plow as a special bolt. I don't know what makes it special. I do know it is meant to shear if you hit a rock or something else to prevent more serious damage. From my experience I use a grade two in that position and a length that will allow the full diameter, (not the threaded portion), to be at the joint or seam between the gusset plate and the stub beam. For the upper bolt that holds the frame, gusset plate, and stub beam I use a grade 8 as you don't want that one to shear or to be partially sheared as it is a lot harder to replace especially on my roll over plow as it also holds the opposite such parts too and a partially sheared bolt is very difficult to remove if the other end has been sheared off. May not apply to a non roll over. Still I would recommend a grade 8 for the main pivot bolt and of a length that doesn't have threads where the shear will be. The coulters also look to be AC to me. The tail wheel looks like it could have been a bolt on option, not a farmer made add on as the S curve wouldn't have been done by the average person adding such.
 
Back to top
View user's profile
wolfman
Tractor Expert


Joined: 16 Apr 1999
Posts: 2633


Report to Moderator

PostPosted: Sat Apr 24, 2021 4:13 pm    Post subject: Re: Allis Chalmers Plow model question Reply to specific post Reply with quote

Your basic model 62 with a lot of homemade hitch and tailwheel jerryrigging. I have a new landslide for an AC mounted plow in the shed.
 
Back to top
View user's profile
DrAllis
Tractor Expert


Joined: 18 Jan 2015
Posts: 1586


Report to Moderator

PostPosted: Sat Apr 24, 2021 4:49 pm    Post subject: Re: Allis Chalmers Plow model question Reply to specific post Reply with quote

60/62 series have angled beams for the bottoms to connect to, similar to the 70 series. That is a 50/52 series because they are straight down beams.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters