Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

WD45


 
Post new topic    
View previous topic :: View next topic  
Author Message
Gtidwell
Long Time User


Joined: 13 Jul 2018
Posts: 1065


Report to Moderator

PostPosted: Tue Apr 27, 2021 2:53 pm    Post subject: WD45 Reply to specific post Reply with quote

I have one that is stuck in third gear. Is it hard to get it out of gear and what is the process? Do I just pull the top off and reset forks? If so, how do I make sure I have them back correctly? All the help will be appreciated.
 
Back to top
View user's profile
rustred
Tractor Guru


Joined: 01 Jul 2009
Posts: 34843


Report to Moderator

PostPosted: Tue Apr 27, 2021 3:34 pm    Post subject: Re: WD45 Reply to specific post Reply with quote

straight forward ,pull the top, once in neutral the rails will be lines up. dont think you need any help. lol.
 
Back to top
View user's profile
Traditional Farmer
Tractor Guru


Joined: 26 Apr 2007
Posts: 22528


Report to Moderator

PostPosted: Tue Apr 27, 2021 4:39 pm    Post subject: Re: WD45 Reply to specific post Reply with quote

Pull the shift lever out usually can take a large screw driver and put it back into neutral,get a flashlight to see what you need to do.
 
Back to top
View user's profile
Gtidwell
Long Time User


Joined: 13 Jul 2018
Posts: 1065


Report to Moderator

PostPosted: Tue Apr 27, 2021 6:11 pm    Post subject: Re: WD45 Reply to specific post Reply with quote

Thank y'all for the advise. Now just to do it. Going to wait until all this rain passes. I don't have a shop to work in.
 
Back to top
View user's profile
Aaron SEIA
Tractor Expert


Joined: 16 Dec 2003
Posts: 2524
Location: SE Iowa

Report to Moderator

PostPosted: Wed Apr 28, 2021 2:51 am    Post subject: Re: WD45 Reply to specific post Reply with quote

Should just be able to pull the shift lever and line things back up through the hole. While the lever is out, check the specs of it. There is a drawing floating around the internet with the dimensions of the ball. You can buy a new aftermarket lever or repair the one you have.
AaronSEIA
 
Back to top
View user's profile
Leroy K
New User


Joined: 03 Oct 2006
Posts: 6


Report to Moderator

PostPosted: Sat May 01, 2021 6:04 pm    Post subject: Re: WD45 Reply to specific post Reply with quote

Mine did this
So
Do as others say
Pull up lever
Flashlight to put into desired gear
There is a key on the side and top of lever
I had to weld/ rebuild the key slot and repair the lever and housing
Then it is better and does not pop out of gear as much

Maybe yours needs this repair
 
Back to top
View user's profile
Gtidwell
Long Time User


Joined: 13 Jul 2018
Posts: 1065


Report to Moderator

PostPosted: Sat May 01, 2021 8:19 pm    Post subject: Re: WD45 Reply to specific post Reply with quote

Thanks to everyone for information. I will check it out good.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters