Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

806 Farmall Shifting


 
Post new topic    
View previous topic :: View next topic  
Author Message
ml44special
Regular


Joined: 09 Jun 2013
Posts: 50


Report to Moderator

PostPosted: Mon May 03, 2021 12:36 pm    Post subject: 806 Farmall Shifting Reply to specific post Reply with quote

Everyone,

I have an 806 that grinds and doesn't go into high range. it does go into reverse, but seems to be all the way out of adjustment.

What else is there we need to do??

Can anyone walk me through the process of repair? Does it need to be split or just top taken off?

Let me know

Matt
 
Back to top
View user's profile
fastfarmall
Tractor Guru


Joined: 05 Feb 2015
Posts: 5936


Report to Moderator

PostPosted: Mon May 03, 2021 2:41 pm    Post subject: Re: 806 Farmall Shifting Reply to specific post Reply with quote

Has it jumped out of reverse yet,Its not to serious,Take the top cover off between the clutch and brake pedals ,Blow the dust and and crap off that cover and remove,There is a cam and roller mechanism in there, I had sheared the roll pin off that controls the forward reverse mechanism. So do u have a IHC dealer you might need a new roller or something, it will show some wear, My 806 has a cab on it,i got tired of standing on the step, bending over, but mine hasn't bothered for almost 40 years now !!!!
 
Back to top
View user's profile
caterpillar guy
Tractor Guru


Joined: 24 Jun 2007
Posts: 7232


Report to Moderator

PostPosted: Tue May 04, 2021 3:30 am    Post subject: Re: 806 Farmall Shifting Reply to specific post Reply with quote

Well it's time to clean off the lid after you check all the pins through the vertical shafts and the linkage for looseness. Then with lid removed check for slop in the bushing going through the top of the lid. And all other points of looseness. Watch those rollers on the pins don't fall in when you remove the lid. There is a row of bolts around it and the park brake needs to be held up after disconnection. If the bushing through the lid is loose which it will be you have 2 choices 1 bore the lid and rebush. 2 a new lid.
 
Back to top
View user's profile
ml44special
Regular


Joined: 09 Jun 2013
Posts: 50


Report to Moderator

PostPosted: Tue May 04, 2021 5:08 am    Post subject: Re: 806 Farmall Shifting Reply to specific post Reply with quote

Anyone have any photos? Diagrams ? Thanks for the help, I will be tearing into it tonight.

Matt
 
Back to top
View user's profile
caterpillar guy
Tractor Guru


Joined: 24 Jun 2007
Posts: 7232


Report to Moderator

PostPosted: Tue May 04, 2021 3:17 pm    Post subject: Re: 806 Farmall Shifting Reply to specific post Reply with quote

No pictures nor video. Was working on mine before all that stuff was around. When you pull the lid off there is a roller on the pin to the high low fork be careful not to loos it inside. IF you do you will be looking for it so it doesn't get in a gear. If you do drop it in you might with the oil drained beable to fish it out with a magnet from the reverse cover on the left side behind the step. It is a rectangle shaped cover with the corner clipped off of it. Removal of the range lid is pretty self explanatory once you see it. There is a pin just above the transmission on the right side that can break causing it to not shift. And then the cam roll pin inside and the linkage up under the cowl like piece in front of the steering wheel.
 
Back to top
View user's profile
ml44special
Regular


Joined: 09 Jun 2013
Posts: 50


Report to Moderator

PostPosted: Wed May 05, 2021 5:14 am    Post subject: Re: 806 Farmall Shifting Reply to specific post Reply with quote

Well, it is not the linkages on the outside of the transmission. Will be pulling the lid and looking this weekend. Hope it is not a gear, as it seems to get close then just grinds and I had the linkage pried all the way back on the outside. Has anyone had bad gears before? or if I replace pins, and sloppy connections solve the problem?

Thanks for the help guys
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters