Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Super A Swinging Drawbar fit 1940 Standard A


 
Post new topic    
View previous topic :: View next topic  
Author Message
sald
Regular


Joined: 06 Jul 2018
Posts: 242


Report to Moderator

PostPosted: Thu May 06, 2021 10:14 am    Post subject: Super A Swinging Drawbar fit 1940 Standard A Reply to specific post Reply with quote

Hello
Been a while since I was on.
I was wondering if the Anchor/Draw Bar Arm for the Super A fit my standard 1940 A? I found different numbers but not sure they are physically interchangeable.
55246DX vs 69425DX Anchor (A vs SA)
55242DX vs 69422DX Bar (A vs SA)
 
Back to top
View user's profile
sald
Regular


Joined: 06 Jul 2018
Posts: 242


Report to Moderator

PostPosted: Thu May 06, 2021 10:32 am    Post subject: Re: Super A Swinging Drawbar fit 1940 Standard A Reply to specific post Reply with quote

I am willing to cut and weld to make it work if there is a major issue.
 
Back to top
View user's profile
gene bender
Tractor Guru


Joined: 28 Jun 2009
Posts: 11286


Report to Moderator

PostPosted: Fri May 07, 2021 5:00 am    Post subject: Re: Super A Swinging Drawbar fit 1940 Standard A Reply to specific post Reply with quote

The same mule drive for the Woods mowers fit so will the drawbar stuff you want
 
Back to top
View user's profile
sald
Regular


Joined: 06 Jul 2018
Posts: 242


Report to Moderator

PostPosted: Fri May 07, 2021 5:47 am    Post subject: Re: Super A Swinging Drawbar fit 1940 Standard A Reply to specific post Reply with quote

Thanks.
I saw that the draw bar is one piece and later for the SA it was three. The anchor and the bar have no dimensions. Thanks Gene!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters