Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

CR rake... bar installation


 
Post new topic    
View previous topic :: View next topic  
Author Message
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6489


Report to Moderator

PostPosted: Thu May 06, 2021 6:42 pm    Post subject: CR rake... bar installation Reply to specific post Reply with quote

What is the best way to reinstall one of the bars on a CR rake. I got the end repaired but I cant line up the hole to install it (too long) Does a person have to loosen the rest of the bars or just have the cast end caps in as far as they can go for installation?
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2994


Report to Moderator

PostPosted: Fri May 07, 2021 6:03 am    Post subject: Re: CR rake... bar installation Reply to specific post Reply with quote

There is a note in setup book. There may be slight difficulty installing the six bolts through the reel supports. To remedy this temporarily loosen the jam nuts on both ends of the 9 stripper bars
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6489


Report to Moderator

PostPosted: Fri May 07, 2021 3:03 pm    Post subject: Re: CR rake... bar installation Reply to specific post Reply with quote

Im not sure that is going to do it. I just need to install one bar on to each end of the steel disc. Im about 1 past the hole with the other end installed.
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2994


Report to Moderator

PostPosted: Sat May 08, 2021 5:15 am    Post subject: Re: CR rake... bar installation Reply to specific post Reply with quote

Should go back on same way as came off.
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6489


Report to Moderator

PostPosted: Sat May 08, 2021 5:44 am    Post subject: Re: CR rake... bar installation Reply to specific post Reply with quote

It should but there was extra play in the worn end so it came off more easily.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters