Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

7110 magnum


 
Post new topic    
View previous topic :: View next topic  
Author Message
laj
New User


Joined: 15 Apr 2013
Posts: 1


Report to Moderator

PostPosted: Mon Apr 15, 2013 4:57 am    Post subject: 7110 magnum Reply to specific post Reply with quote

i have a 7110 and the 3pt will not work rightis there some one that knows how 2 fix them that can tell me how 2 fix it
 
Back to top
View user's profile
Eric in IL
Tractor Expert


Joined: 02 Dec 2005
Posts: 2340


Report to Moderator

PostPosted: Mon Apr 15, 2013 5:57 am    Post subject: Re: 7110 magnum Reply to specific post Reply with quote

Sure, but you are going to be limited to the mechanics whom can also read crystal balls.
 
Back to top
View user's profile
dwag
Long Time User


Joined: 13 Jul 2004
Posts: 1371


Report to Moderator

PostPosted: Mon Apr 15, 2013 9:37 am    Post subject: Re: 7110 magnum Reply to specific post Reply with quote

Check for a fault code on display located by knob control/adjustments.
 
Back to top
View user's profile
pete 23
Tractor Guru


Joined: 10 Sep 2009
Posts: 7530


Report to Moderator

PostPosted: Mon Apr 15, 2013 5:49 pm    Post subject: Re: 7110 magnum Reply to specific post Reply with quote

Usually a potentiometer problem, either at rock shaft of hitch or operating lever. Could also be the draft control pins. CAUTION, working around those electronic controled hitchs can and is very dangerous. Just a touch in wrong place and hitch can and will go all the way up or down. Been a few guys hurt on them not knowing what they are doing. Also, there are a couple of special tools to hook into computer to make tests and adjustments. If you are familiar with them you can do it without but need to know what you are doing. Me, been too long since I worked on them.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters