Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Removing the injector sleeves on a IH D310 engine


 
Post new topic    
View previous topic :: View next topic  
Author Message
hfarmall
Regular


Joined: 02 May 2005
Posts: 80


Report to Moderator

PostPosted: Mon Jan 01, 2018 10:29 am    Post subject: Removing the injector sleeves on a IH D310 engine Reply to specific post Reply with quote

Hi, what tool can you use to remove the injector sleeves on a d310.
THANKS,
 
Back to top
View user's profile
430WLPG
Long Time User


Joined: 03 Aug 2004
Posts: 1327


Report to Moderator

PostPosted: Mon Jan 01, 2018 11:11 am    Post subject: Re: Removing the injector sleeves on a IH D310 engine Reply to specific post Reply with quote

Seems like you use a 7/8 tap cut threads in use and use a
7/8 bolt hooked on a slide hammer and put something in the
bottom of the sleeve to keep shavings out of cylinder
 
Back to top
View user's profile
430WLPG
Long Time User


Joined: 03 Aug 2004
Posts: 1327


Report to Moderator

PostPosted: Mon Jan 01, 2018 4:47 pm    Post subject: Re: Removing the injector sleeves on a IH D310 engine Reply to specific post Reply with quote

There is a special tool to install them it's the shape of the injector a it drives them in at the taper at the bottom
 
Back to top
View user's profile
hfarmall
Regular


Joined: 02 May 2005
Posts: 80


Report to Moderator

PostPosted: Mon Jan 01, 2018 5:13 pm    Post subject: Re: Removing the injector sleeves on a IH D310 engine Reply to specific post Reply with quote

Do you know where I could locate one of those tools.

Thanks for you help
 
Back to top
View user's profile
used red MN
Tractor Expert


Joined: 24 Aug 2013
Posts: 1801
Location: Coon Rapids, MN

Report to Moderator

PostPosted: Mon Jan 01, 2018 10:10 pm    Post subject: Re: Removing the injector sleeves on a IH D310 engine Reply to specific post Reply with quote

I would post this on the Farmall and IH board. Most likely get an answer there.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tool Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters