Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

wc hub thread size


 
Post new topic    
View previous topic :: View next topic  
Author Message
RR Performance
New User


Joined: 26 Aug 2013
Posts: 5


Report to Moderator

PostPosted: Tue Jan 28, 2014 9:33 am    Post subject: wc hub thread size Reply to specific post Reply with quote

Can anyone tell me the thread size and pitch for the holes in the rear wheel hubs of a wc? Where the wheel bolts to the hub. Thank you.
 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Tue Jan 28, 2014 12:54 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

IIRC 5/8 coarse. Std coarse is 11 tpi? Not near my books or tractors. Heck, not even MN! Other end of the river.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 86090
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Tue Jan 28, 2014 1:10 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

Now I know why it is getting so cold down south you drug it with you. You know there are a number of guys who think you should have left the cold up there
 
Back to top
View user's profile
RR Performance
New User


Joined: 26 Aug 2013
Posts: 5


Report to Moderator

PostPosted: Tue Jan 28, 2014 1:35 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

Thank you for the answer.
Ryan
 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Tue Jan 28, 2014 2:35 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

I thought I did- it was minus 16 when I left it there last Tuesday. Currently freezing rain in NO! Parked for awhile.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 86090
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Tue Jan 28, 2014 2:39 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

Hope your not driving around down there. Them people in the south once so much as a flake of snow hits the ground drive like they are in bumper cars and keeping between the ditch is impossible for them
 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Tue Jan 28, 2014 7:45 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

Tried to find a restaurant open for supper.......all closed within many miles, found a McD. Bought some groc this AM but wanted to save that for Wed if needed. Mostly cops and town utility folks on the road, just monitoring. Interstates closed down, lotsa other roads as well.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 86090
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Tue Jan 28, 2014 8:00 pm    Post subject: Re: wc hub thread size Reply to specific post Reply with quote

Ya down in the south they get an inch of snow they close the road till it has gotten above freezing. Still remember a number of years back when a cop pulled my dad over for driving on a snow covered road with maybe 1-2 inches. My dad asked the cop why and he said road are not safe and may dad told him what the heck this is nothing compared to what we had in Minnesota. Cop said you from MN my dad said yes so the cop said go right ahead. Or another time my dad won a bet with home MS High way patrol. The roads had ice on them and my dad was teaching a criminal justice class with them. The y saw where he was parked and said there is not way your going to pull out of there with out spinning you back tires. My dad said you want to bet me on that?? They said yes. Well he did not spin his back tires but did spin the fronts a tad bit. He had borrowed my car which was front wheel drive. They lost the bet and had to pay up
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters