Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1950 Case VAC hydraulics


 
Post new topic    
View previous topic :: View next topic  
Author Message
Gary Millard
New User


Joined: 28 May 2014
Posts: 1


Report to Moderator

PostPosted: Wed May 28, 2014 6:07 pm    Post subject: 1950 Case VAC hydraulics Reply to specific post Reply with quote

Just wondering if someone knows how to check the hydraulic oil in a Case VAC 1950's era tractor...
 
Back to top
View user's profile
Christopher Mikesell
Long Time User


Joined: 09 Aug 2011
Posts: 900


Report to Moderator

PostPosted: Wed May 28, 2014 7:04 pm    Post subject: Re: 1950 Case VAC hydraulics Reply to specific post Reply with quote

There is a plug on the left side of the torque tube above the hydraulic filter opening. The hydraulic fluid should be level with this plug when the tractor is sitting level. Also, some loader-equipped tractors had an elbow installed in this plug to allow the torque tube to hold more oil to accommodate the loader's one-way hydraulic cylinders.
 
Back to top
View user's profile
Joe (Wa)
Tractor Expert


Joined: 01 Jan 1999
Posts: 3225


Report to Moderator

PostPosted: Wed May 28, 2014 7:10 pm    Post subject: Re: 1950 Case VAC hydraulics Reply to specific post Reply with quote

Pipe plug on the left side of the torque tube just forward of the clutch pedal. Full is to the lip of the plug opening.

1950"s VA will be the same or similar to this pic.

Joe

 
Back to top
View user's profile
Bret4207
Tractor Guru


Joined: 15 Jan 2005
Posts: 13082
Location: St Lawrence Valley, Northern NY

Report to Moderator

PostPosted: Thu May 29, 2014 3:43 am    Post subject: Re: 1950 Case VAC hydraulics Reply to specific post Reply with quote

Gary Millard wrote:
(quoted from post at 19:07:46 05/28/14) Just wondering if someone knows how to check the hydraulic oil in a Case VAC 1950's era tractor...


Not trying to be a smart aleck, but operators manuals are available on ebay pretty cheap. Good thing to have.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters