Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

D17 clutch kit


 
Post new topic    
View previous topic :: View next topic  
Author Message
mikebol250
Regular


Joined: 18 Apr 2016
Posts: 28


Report to Moderator

PostPosted: Mon Apr 18, 2016 3:38 pm    Post subject: D17 clutch kit Reply to specific post Reply with quote

I'm getting ready to put a clutch kit in my 1964 D 17 Gas motor.
Why isn't a clutch alignment tool in the kit?
There isn't much wiggle room for the disc but there is some.

 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Mon Apr 18, 2016 9:30 pm    Post subject: Re: D17 clutch kit Reply to specific post Reply with quote

Some folks just use a cut off shaft for that.
 
Back to top
View user's profile
hd6gtom
Tractor Guru


Joined: 20 Jan 2011
Posts: 4777


Report to Moderator

PostPosted: Tue Apr 19, 2016 4:52 am    Post subject: Re: D17 clutch kit Reply to specific post Reply with quote

Mike align the edge of the clutch disk with the edge of the pressure plate and slide her back together.
 
Back to top
View user's profile
mikebol250
Regular


Joined: 18 Apr 2016
Posts: 28


Report to Moderator

PostPosted: Tue Apr 19, 2016 1:00 pm    Post subject: Re: D17 clutch kit Reply to specific post Reply with quote

CVPost-JMS/.MN wrote:
(quoted from post at 22:30:25 04/18/16) Some folks just use a cut off shaft for that.


Thank you!
 
Back to top
View user's profile
mikebol250
Regular


Joined: 18 Apr 2016
Posts: 28


Report to Moderator

PostPosted: Tue Apr 19, 2016 1:01 pm    Post subject: Re: D17 clutch kit Reply to specific post Reply with quote

That sounds like it will work good thank you.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters