Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

AC Front Spindles


 
Post new topic    
View previous topic :: View next topic  
Author Message
Todd Young
Regular


Joined: 05 Mar 2009
Posts: 121


Report to Moderator

PostPosted: Sat Mar 12, 2016 10:10 pm    Post subject: AC Front Spindles Reply to specific post Reply with quote

The L & R axel arm shafts are worn bad on my allis chalmers wd. Can these be taken apart to get on a lathe, or is there replacements? Part a has grooves that need to be built up and turned down, but the assembly won't fit on my lathe. This is the part that goes up in the knee and has the axel.

Thanks,

Todd
 
Back to top
View user's profile
Aaron SEIA
Tractor Expert


Joined: 16 Dec 2003
Posts: 2459
Location: SE Iowa

Report to Moderator

PostPosted: Sun Mar 13, 2016 4:52 am    Post subject: Re: AC Front Spindles Reply to specific post Reply with quote

There are reproduction spindles out there. Never had one apart but I think there are bushings in the spindle housing as well.
AaronSEIA
 
Back to top
View user's profile
4wdtom
Tractor Expert


Joined: 03 Oct 2014
Posts: 1938


Report to Moderator

PostPosted: Sun Mar 13, 2016 7:03 am    Post subject: Re: AC Front Spindles Reply to specific post Reply with quote

Maybe it is time for you to look for a larger lathe, a good excuse to buy one. It would be an interesting project to turn one of these, you would have to swing the hub spindle over the lathe and work inside it, between it and the chuck.And to turn the top bushing area you might get in a chuck, gut the other end would be hanging way out, support by tailstock center or steady rest I guess. Where are you? I am in R.I. and have a 12" Lodge and Shipley that measures out more like a 14", it might fit.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 87024
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Sun Mar 13, 2016 9:14 am    Post subject: Re: AC Front Spindles Reply to specific post Reply with quote

In the long run you might be better off finding some one with a parts WD to get them from. I know lots of us have parts tractor laying around. I know I have most of a WD out back that still has a lot of good parts on it
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters