Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

180


 
Post new topic    
View previous topic :: View next topic  
Author Message
rickymotorbrains
Regular


Joined: 04 Mar 2011
Posts: 100
Location: ky

Report to Moderator

PostPosted: Thu Apr 14, 2016 4:04 pm    Post subject: 180 Reply to specific post Reply with quote

can anyone tell me if the 170 transmission back will work on a 180
 
Back to top
View user's profile MSN Messenger
Eldon (WA)
Tractor Guru


Joined: 11 Apr 2010
Posts: 4540
Location: washington

Report to Moderator

PostPosted: Thu Apr 14, 2016 4:34 pm    Post subject: Re: 180 Reply to specific post Reply with quote

CVPost-rickymotorbrains wrote:
(quoted from post at 17:04:06 04/14/16) can anyone tell me if the 170 transmission back will work on a 180


I know the finals are the same, but I don't think the transmissions will interchange...top shaft is probably different. I have one of each laying here, but they both have the torque tubes on them yet.
 
Back to top
View user's profile
rickymotorbrains
Regular


Joined: 04 Mar 2011
Posts: 100
Location: ky

Report to Moderator

PostPosted: Thu Apr 14, 2016 5:31 pm    Post subject: Re: 180 Reply to specific post Reply with quote

where you located at and you selling the 180
 
Back to top
View user's profile MSN Messenger
DrAllis
Long Time User


Joined: 18 Jan 2015
Posts: 1475


Report to Moderator

PostPosted: Thu Apr 14, 2016 6:10 pm    Post subject: Re: 180 Reply to specific post Reply with quote

When you say the "back" of the transmission, are you referring to the lift arm housing, where the PTO shaft protrudes from?? If so, yes, that housing will interchange between a 170 and 180. The transmissions internally are completely different, as are the transmission housings. The final drives will interchange, but are not the same, as they are different ratios and gear widths for strength on the 180.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters