Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Super H pto seal


 
Post new topic    
View previous topic :: View next topic  
Author Message
SuperHank
Regular


Joined: 27 Aug 2001
Posts: 355


Report to Moderator

PostPosted: Thu Mar 02, 2017 1:48 pm    Post subject: Super H pto seal Reply to specific post Reply with quote

I ordered a replacement seal from YT and pulled the old one (did that backwards) and the new seal is 1/3 the width of the old seal. The new thinner seal may work but should I look for the old style or is the new seal adequate.
 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 36438
Location: St. Cloud, MN

Report to Moderator

PostPosted: Thu Mar 02, 2017 1:57 pm    Post subject: Re: Super H pto seal Reply to specific post Reply with quote

The new seal is an advantage because you can position it in an unworn spot on the shaft. Use 400 grit paper and polish the shaft at the point of seal contact. Round and round, not in and out. Hold the paper and spin the shaft. Otherwise the tiny scratches eat the new seal. Jim
 
Back to top
View user's profile
cuby
Long Time User


Joined: 21 May 2015
Posts: 827


Report to Moderator

PostPosted: Thu Mar 02, 2017 3:21 pm    Post subject: Re: Super H pto seal Reply to specific post Reply with quote

You may be able to put 2 seals in that same place with the second one being a backup seal.
 
Back to top
View user's profile
Goose
Tractor Guru


Joined: 30 Jun 2007
Posts: 10661


Report to Moderator

PostPosted: Thu Mar 02, 2017 4:31 pm    Post subject: Re: Super H pto seal Reply to specific post Reply with quote

I did a PTO seal on an H a couple of years ago. If I remember right, I put two back to back.
 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 36438
Location: St. Cloud, MN

Report to Moderator

PostPosted: Thu Mar 02, 2017 5:16 pm    Post subject: Re: Super H pto seal Reply to specific post Reply with quote

Remember to put chassis grease on the lips and back of the seals. If using 2, put grease between them to keep the outer seal lubed. Jim
 
Back to top
View user's profile
Oregon Tractor Jack
Long Time User


Joined: 16 Aug 2013
Posts: 942


Report to Moderator

PostPosted: Thu Mar 02, 2017 7:49 pm    Post subject: Re: Super H pto seal Reply to specific post Reply with quote

Don't think they make the doubles anymore. I think those were used in extreme conditions like the pto shaft. Do as suggested, double up or find a "good spot" on the shaft. I have done both depending on the location and the condition of the shaft. Always grease the seal when assembling.

OTJ
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters