Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

robgIN or others, how do I install the pump?


 
Post new topic    
View previous topic :: View next topic  
Author Message
n9lhm
Regular


Joined: 24 Apr 2005
Posts: 447


Report to Moderator

PostPosted: Thu Jul 27, 2017 4:25 pm    Post subject: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

So I've got this belly pump all ready to mount on my F-20, and........ it won't fit. It looks like there is enough clearance for the pump to sit in there after it's on the mounting studs, but you can't get it over the studs without running into the clutch housing. So how do you mount it? You don't have to unbolt the whole engine and move it forward, do you?
 
Back to top
View user's profile
robgIN
Long Time User


Joined: 06 Apr 2008
Posts: 1399


Report to Moderator

PostPosted: Thu Jul 27, 2017 4:36 pm    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

Its been a few years but I think I installed mine while I had the clutch out. It is pretty easy to remove the clutch cover and that would give you the clearance you need, easier than moving the engine forward .
 
Back to top
View user's profile
n9lhm
Regular


Joined: 24 Apr 2005
Posts: 447


Report to Moderator

PostPosted: Thu Jul 27, 2017 7:04 pm    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

OK, looking at the parts book, the clutch cover is definitely what is in the way, however, if I take the clutch cover off and mount the pump, how do I get the clutch cover back on? It looks like you need a 2" or better straight shot to get the clutch shaft back in the pressure plate and the pilot bearing?
 
Back to top
View user's profile
used red MN
Tractor Expert


Joined: 24 Aug 2013
Posts: 2729
Location: Coon Rapids, MN

Report to Moderator

PostPosted: Fri Jul 28, 2017 2:40 am    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

No idea about the configuration your working with, but could you double nut the studs remove them and reinstall once it is in place?
 
Back to top
View user's profile
used red MN
Tractor Expert


Joined: 24 Aug 2013
Posts: 2729
Location: Coon Rapids, MN

Report to Moderator

PostPosted: Fri Jul 28, 2017 2:47 am    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

Should add for you to beware if the studs screw in the transmission side the lube may leak out the holes when their out. So you may have to drain down the rear end to below the stud hole level during the pump install. FYI, I have rarely been around any F20, so shooting in the dark.
 
Back to top
View user's profile
BruceS
Regular


Joined: 19 Mar 2008
Posts: 121


Report to Moderator

PostPosted: Fri Jul 28, 2017 5:37 am    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

yes, you do have to move the engine forward to get clearence. I can't see that removing the clutch cover would work. you'd have the same problem with clearance when putting it back.
 
Back to top
View user's profile
robgIN
Long Time User


Joined: 06 Apr 2008
Posts: 1399


Report to Moderator

PostPosted: Fri Jul 28, 2017 8:46 am    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

if you rotate the clutch cover as you go in , it will go. That's how I have done it on two different F-20s with belly pump
 
Back to top
View user's profile
robgIN
Long Time User


Joined: 06 Apr 2008
Posts: 1399


Report to Moderator

PostPosted: Fri Jul 28, 2017 1:40 pm    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

I didn't move the engine forward to do the two of mine. The shaft that engages the clutch disc can be pulled out of the clutch cover also and then put in after the cover is in place. You do not have to move the engine forward.
 
Back to top
View user's profile
robgIN
Long Time User


Joined: 06 Apr 2008
Posts: 1399


Report to Moderator

PostPosted: Fri Jul 28, 2017 1:44 pm    Post subject: Re: robgIN or others, how do I install the pump? Reply to specific post Reply with quote

also you can take the pilot shaft out of the clutch cover and get the cover in place and then put the pilot shaft back through the cover into the clutch disc. Pretty sure that is what I did because I have never moved the engine forward to install anything.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters