Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

A clutch drive shaft


 
Post new topic    
View previous topic :: View next topic  
Author Message
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2021
Location: Eugene Oregon

Report to Moderator

PostPosted: Sun Jan 14, 2018 11:41 am    Post subject: A clutch drive shaft Reply to specific post Reply with quote

What holds the drive shaft in the trans. Trying to get new engine lined up but won't go on. I don't know if shafts are different size, pilot bearing. Thought may the shaft slipped out. Time to go take some more accurate measurements. Probably just not holding my tongue right.
 
Back to top
View user's profile
Phil Tibbetts
Tractor Expert


Joined: 23 Jul 2004
Posts: 2043
Location: Old Town, Maine

Report to Moderator

PostPosted: Sun Jan 14, 2018 12:40 pm    Post subject: Re: A clutch drive shaft Reply to specific post Reply with quote

try putting the tranny in neutral an engage the PTO lever, then have someone turn the PTO shaft slowly while you try to get it to go together. I'm assuming you used an alignment shaft when you installed the clutch to the flywheel. Sometimes they can be a pain on any tractor, then all at once it goes.
 
Back to top
View user's profile
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2021
Location: Eugene Oregon

Report to Moderator

PostPosted: Sun Jan 14, 2018 1:10 pm    Post subject: Re: A clutch drive shaft Reply to specific post Reply with quote

CVPost-Phil Tibbetts wrote:
(quoted from post at 13:40:00 01/14/1Cool try putting the tranny in neutral an engage the PTO lever, then have someone turn the PTO shaft slowly while you try to get it to go together. I'm assuming you used an alignment shaft when you installed the clutch to the flywheel. Sometimes they can be a pain on any tractor, then all at once it goes.


Unfortunately I'm by myself today. Trying to turn the pulley as I wiggle it in.
As of now I took the clutch and flywheel off. In the process I noticed the outer ring on the flywheel was broke so I pulled everything off the other engine and I'm working on flipping the ring gear now.
 
Back to top
View user's profile
Phil Tibbetts
Tractor Expert


Joined: 23 Jul 2004
Posts: 2043
Location: Old Town, Maine

Report to Moderator

PostPosted: Sun Jan 14, 2018 2:56 pm    Post subject: Re: A clutch drive shaft Reply to specific post Reply with quote

If you are alone try just turning the shaft slightly and keep trying it. Some of the transmission shafts have the ends of the spline beveled to help. Don't know about the A.
 
Back to top
View user's profile
khouse6
Long Time User


Joined: 12 Apr 2014
Posts: 685


Report to Moderator

PostPosted: Sun Jan 14, 2018 3:12 pm    Post subject: Re: A clutch drive shaft Reply to specific post Reply with quote

if you had the clutch disc and pressure plate off, you need to align the clutch disc.
 
Back to top
View user's profile
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2021
Location: Eugene Oregon

Report to Moderator

PostPosted: Sun Jan 14, 2018 6:01 pm    Post subject: Re: A clutch drive shaft Reply to specific post Reply with quote

CVPost-khouse6 wrote:
(quoted from post at 16:12:11 01/14/1Cool if you had the clutch disc and pressure plate off, you need to align the clutch disc.

I hadn't removed it then. I was going to flip the ring gear but have decided to order a new one
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters