Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Lug bolts


 
Post new topic    
View previous topic :: View next topic  
Author Message
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2088
Location: Eugene Oregon

Report to Moderator

PostPosted: Fri Feb 16, 2018 7:03 pm    Post subject: Lug bolts Reply to specific post Reply with quote

Putting some steel wheels on a Oliver 66. The factory bolts go into the taper quite a ways. Do you guys use them, use one with a bigger head, put a stud in or do something else? Thank you
 
Back to top
View user's profile
Dblair
Tractor Expert


Joined: 07 Nov 2007
Posts: 2783


Report to Moderator

PostPosted: Sat Feb 17, 2018 6:22 am    Post subject: Re: Lug bolts Reply to specific post Reply with quote

use a backup ring with the steel wheels and yes I use the taper lug bolts.

 
Back to top
View user's profile
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2088
Location: Eugene Oregon

Report to Moderator

PostPosted: Sat Feb 17, 2018 9:07 am    Post subject: Re: Lug bolts Reply to specific post Reply with quote

I picked up some 18.4-38. (thank you Arlen) the mounting holes are larger than the Oliver wheels. They will only be going on the 66 temporary and I will probably be moving them to my 77 or 88 later. Stock lug nuts would work for temporary use but I don't want them to be permanent. Thank you for your suggestion.
 
Back to top
View user's profile
Dblair
Tractor Expert


Joined: 07 Nov 2007
Posts: 2783


Report to Moderator

PostPosted: Sat Feb 17, 2018 4:40 pm    Post subject: Re: Lug bolts Reply to specific post Reply with quote

put studs in the 9/16 holes and lug nuts on them which have a larger nut that fits a 7/8 wrench . I just drilled the wheel threw and put 9/16 grade 8 bolts in and put the nuts on the 9/16 lug
nuts on my 770 oliver . couldn't get a picture tonight .
 
Back to top
View user's profile
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2088
Location: Eugene Oregon

Report to Moderator

PostPosted: Sat Feb 17, 2018 5:12 pm    Post subject: Re: Lug bolts Reply to specific post Reply with quote

CVPost-dblair wrote:
(quoted from post at 17:40:31 02/17/1Cool put studs in the 9/16 holes and lug nuts on them which have a larger nut that fits a 7/8 wrench . I just drilled the wheel threw and put 9/16 grade 8 bolts in and put the nuts on the 9/16 lug
nuts on my 770 oliver . couldn't get a picture tonight .

Thank you. That's what I figure I will have to do unless I can find a bolt with oversized head.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters