Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Hesston 1090? 's


 
Post new topic    
View previous topic :: View next topic  
Author Message
fball1208
Regular


Joined: 14 Jul 2017
Posts: 57


Report to Moderator

PostPosted: Thu Jun 14, 2018 12:18 pm    Post subject: Hesston 1090? 's Reply to specific post Reply with quote

Anyone know what size the shear bolt is? and also what kind of pin is needed in the PTO end. Ours is gone and we have a bolt in it as of now but would like to replace it with a new lock pin.

Thanks
 
Back to top
View user's profile
IanC
Tractor Expert


Joined: 19 Sep 2002
Posts: 2156


Report to Moderator

PostPosted: Thu Jun 14, 2018 1:06 pm    Post subject: Re: Hesston 1090? 's Reply to specific post Reply with quote

Here is a link to the AGCO parts book. I didn't remember a shear bolt in the drive line so I took a look. Left the Hesston dealer in 1991 when those units were still "new". If the PTO shaft has a rectangular cross section then it was still US, not metric (triangular or lemon shaped shafts). It would have used the old type locking pin that stuck all the way through the yoke and had an x-washer clip. Those may be hard to find as the drive line makers stopped using that style and went to a style that didn't protrude out the "back" side of the yoke for safety reasons.
http://www.agcopartsbooks.com/PartsBooksN/Viewer/book.aspx?book=agco/8881427
 
Back to top
View user's profile
riveroadrat
Long Time User


Joined: 26 Nov 2013
Posts: 1344


Report to Moderator

PostPosted: Thu Jun 14, 2018 3:13 pm    Post subject: Re: Hesston 1090? 's Reply to specific post Reply with quote

I dont think I have what you need but I do have some parts for that model.
 
Back to top
View user's profile
fball1208
Regular


Joined: 14 Jul 2017
Posts: 57


Report to Moderator

PostPosted: Fri Jun 15, 2018 12:36 pm    Post subject: Re: Hesston 1090? 's Reply to specific post Reply with quote

CVPost-riveroadrat wrote:
(quoted from post at 16:13:33 06/14/1Cool I dont think I have what you need but I do have some parts for that model.


I am looking for the Pin that attaches the Yoke to the tractor PTO its bigger on one end then the other.
 
Back to top
View user's profile
IanC
Tractor Expert


Joined: 19 Sep 2002
Posts: 2156


Report to Moderator

PostPosted: Fri Jun 15, 2018 1:16 pm    Post subject: Re: Hesston 1090? 's Reply to specific post Reply with quote

Go to the link I gave you and open "gearbox" page 6. The pin for the tractor end yoke is pictured in the lower left hand corner. In the upper left hand corner you will see three little icons that look like a magnifying glass. Click on the right hand one which allows you to make a box around what you need to magnify. If that is what your pin looked like that is the older style pin. Your yoke could have been replaced and use a different style. Look on the castings for a logo, what is coming to mind is Hesston used Rockwell, but it has been a long time.
 
Back to top
View user's profile
fball1208
Regular


Joined: 14 Jul 2017
Posts: 57


Report to Moderator

PostPosted: Fri Jun 15, 2018 6:11 pm    Post subject: Re: Hesston 1090? 's Reply to specific post Reply with quote

Looked at the page and found the part numbers bad part is closest parts dealer to me is 150 miles away
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters