Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

m610 bobcat skid steer


 
Post new topic    
View previous topic :: View next topic  
Author Message
jack in ga
Regular


Joined: 27 Apr 2014
Posts: 25


Report to Moderator

PostPosted: Fri Sep 21, 2018 3:45 pm    Post subject: m610 bobcat skid steer Reply to specific post Reply with quote

My m610 bobcat speed selector valve was leaking on the drive belt. I removed it and had it reworked when I installed it it does not work I have tried to adjust it, but I CAN,T get any pressure reading with a gauge I cant figure why there no pressure there. the bucket will pick up till the back cleares the dirt. this tell me the pump is working.
 
Back to top
View user's profile
jm.
Tractor Guru


Joined: 11 Apr 2010
Posts: 5566
Location: Dover Tenn.

Report to Moderator

PostPosted: Fri Sep 21, 2018 4:04 pm    Post subject: Re: m610 bobcat skid steer Reply to specific post Reply with quote

First check your lines, any chance you got line in the wrong place, that is the most common mistake.
 
Back to top
View user's profile
jack in ga
Regular


Joined: 27 Apr 2014
Posts: 25


Report to Moderator

PostPosted: Fri Sep 21, 2018 4:14 pm    Post subject: Re: m610 bobcat skid steer Reply to specific post Reply with quote

jm the lines going to the selector vale are preformed steel. I removed them from the valve end.only I think something has been installed in the valve wrong.I understand some people are modifying a different valve and replacing the old selector valve. the repair manual shows installing a bold in the return line to see if it will have pressure.
 
Back to top
View user's profile
Charlie
Tractor Expert


Joined: 22 Feb 1998
Posts: 2373


Report to Moderator

PostPosted: Sat Sep 22, 2018 5:57 pm    Post subject: Re: m610 bobcat skid steer Reply to specific post Reply with quote

I would look at the lever that you use to activate the higher speed. Maybe after reworking the valve, it's not moving far enough to let the oil through. You may just have to adjust the limits of travel.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters