Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Exhaust elbow


 
Post new topic    
View previous topic :: View next topic  
Author Message
Gene Sage
Regular


Joined: 07 Jul 2012
Posts: 102
Location: Iowa Falls, IA

Report to Moderator

PostPosted: Fri Oct 19, 2018 4:13 am    Post subject: Exhaust elbow Reply to specific post Reply with quote

Installing a DT 467 engine from a 5288 in a 666. Will the exhaust elbow from a 1066 or 1466 fit on the base and provide a vertical exhaust?
 
Back to top
View user's profile
ejr-IA.
Long Time User


Joined: 19 Oct 2009
Posts: 700


Report to Moderator

PostPosted: Sat Oct 20, 2018 8:23 am    Post subject: Re: Exhaust elbow Reply to specific post Reply with quote

cording to the parts book the elbow should bolt on.Does the exhaust manifold flow to the middle or the rear?
 
Back to top
View user's profile
Gene Sage
Regular


Joined: 07 Jul 2012
Posts: 102
Location: Iowa Falls, IA

Report to Moderator

PostPosted: Sat Oct 20, 2018 1:50 pm    Post subject: Re: Exhaust elbow Reply to specific post Reply with quote

It flows to the middle. The intake side of the turbo is to the rear and and makes a sharp bend to the airfilter. Compressed air from the turbo makes a bend to the front flowing to the intake manifold. How much horsepower will the transmission stand along with the final drive?
 
Back to top
View user's profile
ejr-IA.
Long Time User


Joined: 19 Oct 2009
Posts: 700


Report to Moderator

PostPosted: Sun Oct 21, 2018 10:39 am    Post subject: Re: Exhaust elbow Reply to specific post Reply with quote

Seen quite a few that has done this.Need a double or triple disk clutch, needled rear differential , heavy input shaft, adapter rear for 400 engine,Ta eliminator or reworked TA. Leaman is a name of a guy that has these parts 1 717 464 2874.Have a IH friend that has a large IH collection he has a 560 with the 400 engine in it.
 
Back to top
View user's profile
Gene Sage
Regular


Joined: 07 Jul 2012
Posts: 102
Location: Iowa Falls, IA

Report to Moderator

PostPosted: Sun Oct 21, 2018 2:10 pm    Post subject: Re: Exhaust elbow Reply to specific post Reply with quote

Working with Ed Leaman parts. He is supplying triple disk clutch, TA eliminator shaft, front and rear adapter plates. Not sure about the need for needle bearings in differential. Won't be a serious sanctioned puller, just a few county fairs etc and tractor rides. Probably start with a 11 or 13 mm head in pump and appropriate injectors and Snow water injection. At what point do I need to carry an empty HyGard pail to pick up parts?
 
Back to top
View user's profile
caterpillar guy
Tractor Guru


Joined: 24 Jun 2007
Posts: 3674


Report to Moderator

PostPosted: Mon Oct 22, 2018 2:17 am    Post subject: Re: Exhaust elbow Reply to specific post Reply with quote

From the beginning for a joke with John Deere parts painted on the side .
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters