Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Oliver 99


 
Post new topic    
View previous topic :: View next topic  
Author Message
mfitzpatrick2
New User


Joined: 04 Jan 2019
Posts: 1


Report to Moderator

PostPosted: Fri Jan 04, 2019 4:49 pm    Post subject: Oliver 99 Reply to specific post Reply with quote

Looking for info on early Oliver 99 with 4 cylinder engine

My neighbor has one and is restoring it

Engine is stuck and is taking a lot of work to get pistons out

Cant find much info about them

Where is the serial# located?
 
Back to top
View user's profile
OliverNate
Long Time User


Joined: 16 Apr 2012
Posts: 559


Report to Moderator

PostPosted: Fri Jan 04, 2019 7:01 pm    Post subject: Re: Oliver 99 Reply to specific post Reply with quote

Engine parts are hard to come by, don't think they're any new parts to be found, unless you're lucky enough to come across NOS parts.

Serial number is when sitting in the seat looking forward on the right side of engine, kinda behind the oil filter canister.
 
Back to top
View user's profile
hunt
Regular


Joined: 10 Jun 2012
Posts: 77


Report to Moderator

PostPosted: Sun Jan 06, 2019 6:34 pm    Post subject: Re: Oliver 99 Reply to specific post Reply with quote

I have an engine that was dry stuck. It may have good parts in it. We soaked it down good and were able to get it to turn but it has been 10 years since I put it on the rack. I am in NW Ohio.
 
Back to top
View user's profile
KFFarm
Regular


Joined: 01 Jan 2016
Posts: 72


Report to Moderator

PostPosted: Wed Jan 09, 2019 8:22 pm    Post subject: Re: Oliver 99 Reply to specific post Reply with quote

We are in the midst of one of those exact rebuilds right now. Ours has the 5” piston kit in it. We need sleeves for it, so far no luck finding any. We plan to reuse the pistons with new rings, but the sleeves have some fairly significant rusted areas that we don’t want to trust.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters