Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1850 Brake Replacement


 
Post new topic    
View previous topic :: View next topic  
Author Message
eye4iron
Regular


Joined: 13 Apr 2006
Posts: 407


Report to Moderator

PostPosted: Fri Jan 04, 2019 5:15 pm    Post subject: 1850 Brake Replacement Reply to specific post Reply with quote

I am going to buy some brake discs for my 1850. Is there anything
else I should buy before I start taking it apart?
Is there anything unusual I should watch for when I have it apart?
 
Back to top
View user's profile
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 41399


Report to Moderator

PostPosted: Sat Jan 05, 2019 6:38 am    Post subject: Re: 1850 Brake Replacement Reply to specific post Reply with quote

When you get in there,if there's any oil in there at all,replace the seals on the pinion shaft. Best way to get them out if you have to is drill two small holes in them,put screws in them,wrap a wire around the screws and pull them that way. When you get the actuators out,unhook the springs and split them in half and make sure those balls are clean as a whistle. Be sure all the pivot points on those actuators work free and easy.
 
Back to top
View user's profile
2-stroke DD
Regular


Joined: 08 Mar 2009
Posts: 97


Report to Moderator

PostPosted: Sat Jan 05, 2019 7:03 am    Post subject: Re: 1850 Brake Replacement Reply to specific post Reply with quote

Like rrlund said check for oil and not only clean everything but also replace those 3 springs on each side. Do not use any oil or grease to lubricate anything. If you have dry graphite you can use that to lube the balls. If you have a later model with the shims to adjust the brakes make sure you have all of them to put back in
 
Back to top
View user's profile
IanC
Tractor Expert


Joined: 19 Sep 2002
Posts: 2210


Report to Moderator

PostPosted: Sat Jan 05, 2019 12:56 pm    Post subject: Re: 1850 Brake Replacement Reply to specific post Reply with quote

I would install new balls and springs in the discs. They may not look bad, but for as little as they cost they should be replaced. Taking the discs apart will also allow you to inspect the ramps for wear.
 
Back to top
View user's profile
eye4iron
Regular


Joined: 13 Apr 2006
Posts: 407


Report to Moderator

PostPosted: Sun Jan 06, 2019 10:50 am    Post subject: Re: 1850 Brake Replacement Reply to specific post Reply with quote

Thanks for the info. I will order the seal, springs and balls also.
 
Back to top
View user's profile
gary66
Regular


Joined: 26 Jul 2014
Posts: 254


Report to Moderator

PostPosted: Tue Jan 08, 2019 8:56 pm    Post subject: Re: 1850 Brake Replacement Reply to specific post Reply with quote

if taking them apart doesn't say using anti seize would've been good I'l say it. use it on reassembly.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters