Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

NI sickle bar mower M41


 
Post new topic    
View previous topic :: View next topic  
Author Message
DennyF
Regular


Joined: 22 May 2006
Posts: 330
Location: PA

Report to Moderator

PostPosted: Wed Mar 13, 2019 4:08 pm    Post subject: NI sickle bar mower M41 Reply to specific post Reply with quote

Got a free New Idea mower. Everything is there, but the pitman arm and end connections. Not a problem to whip up another pitman arm, but gonna need the hardware to hook it up.

Doesn't seem to be much info on the M41 mower, as I've spent considerable time looking. Set up for a drawbar mount, has one pony wheel on the back. 7' bar and a beefy, well made unit. TIA.
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 19592
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Wed Mar 13, 2019 6:37 pm    Post subject: Re: NI sickle bar mower M41 Reply to specific post Reply with quote

I know that sounds like a No. 40 mower. Never heard of a number like M41. Check tag again to see if it is actually No. 40 I just sent one to scrap. I only saw 3 on them in my 75 years and the one I had was included in that 3 mowers. And this is about 45 mile from where they were made.
 
Back to top
View user's profile
DennyF
Regular


Joined: 22 May 2006
Posts: 330
Location: PA

Report to Moderator

PostPosted: Thu Mar 14, 2019 3:29 pm    Post subject: Re: NI sickle bar mower M41 Reply to specific post Reply with quote

Yep, it's a Model 41. Noticed while looking up the critter, that hardly any of the NI parts sites even list it, but a few did.
 
Back to top
View user's profile
ET
Tractor Expert


Joined: 31 Jul 2007
Posts: 2351


Report to Moderator

PostPosted: Fri Mar 15, 2019 4:02 am    Post subject: Re: NI sickle bar mower M41 Reply to specific post Reply with quote

If the end hardware clamps to a ball on the section bar you could probably use IH or JD parts on there. They would be easier to find.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters