Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Got it running


 
Post new topic    
View previous topic :: View next topic  
Author Message
Skip Burney
Long Time User


Joined: 25 Oct 2016
Posts: 619


Report to Moderator

PostPosted: Sat Mar 09, 2019 7:39 pm    Post subject: Got it running Reply to specific post Reply with quote

Well I got it running, it wouldnt pump fuel for anything so as a last resort I took a 1 inch box end wrench and hit the fuel pump 5 or 6 times and it started pumping fuel, I hooked up the lines it turned over 5 or 65 times and started right up. It has 70 lbs of oil pressure at idle. Now all I have to do is stop the darned combustion chamber cover leaks

 
Back to top
View user's profile
John Deere D
Tractor Guru


Joined: 14 Jun 2011
Posts: 3986


Report to Moderator

PostPosted: Sat Mar 09, 2019 9:42 pm    Post subject: Re: Got it running Reply to specific post Reply with quote

I'm apprehensive at even suggesting that this has worked for me........(Not an Engineered Procedure)

With GASKETS removed from Precom Caps,Caps set back on head with nuts finger tight..........I have taken a steel KING PIN...placed on PRE. COMP. CAP and waked
KING PIN with Mechanics Hammer.

I believe,after over torquing the PRE CAPS were no longer flat.


Bob...No Guarantees.....Retired Power Engineer
 
Back to top
View user's profile
Jack in NB
Regular


Joined: 14 Aug 2007
Posts: 217


Report to Moderator

PostPosted: Sun Mar 10, 2019 5:59 am    Post subject: Re: Got it running Reply to specific post Reply with quote

I finally had to chuck them up in a lathe.

Tedious, getting the exposed back surface lined up, but once accomplished it was straightforward to shave a bit off the gasket surface to true it up, and then a few thou off the rim of the chamber itself.

In retrospect, I should have made up a block to put in the chuck, to allow fast rechucking the things, in case more needed to be shaved off the cup rim.
 
Back to top
View user's profile
ASEguy
Tractor Expert


Joined: 19 Mar 2010
Posts: 3229


Report to Moderator

PostPosted: Thu Mar 14, 2019 3:08 am    Post subject: Re: Got it running Reply to specific post Reply with quote

Sounds good. Nice job.
 
Back to top
View user's profile
Skip Burney
Long Time User


Joined: 25 Oct 2016
Posts: 619


Report to Moderator

PostPosted: Thu Mar 14, 2019 5:26 pm    Post subject: Re: Got it running Reply to specific post Reply with quote

CVPost-ASEguy wrote:
(quoted from post at 04:08:44 03/14/19) Sounds good. Nice job.


Thanks I just finished making the brackets to mount a small Denso alternator on it
 
Back to top
View user's profile
Skip Burney
Long Time User


Joined: 25 Oct 2016
Posts: 619


Report to Moderator

PostPosted: Thu Mar 14, 2019 6:49 pm    Post subject: Re: Got it running Reply to specific post Reply with quote



Got it mounted and working as it should, I tightened the brackets and the vibration stopped
 
Back to top
View user's profile
ptfarmer
Tractor Guru


Joined: 01 Jul 2013
Posts: 6108


Report to Moderator

PostPosted: Thu Mar 14, 2019 8:38 pm    Post subject: Re: Got it running Reply to specific post Reply with quote

Sounds good, nice job!!!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters