Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

830 cracked heads


 
Post new topic    
View previous topic :: View next topic  
Author Message
Fred eagerton jr.
Guest






Report to Moderator
PostPosted: Mon May 21, 2007 2:38 pm    Post subject: 830 cracked heads Reply to specific post Reply with quote
Ihave a 830 that I got from my uncle, it would not run, sounded like a burnt valve, pulled heads off sunday afternoon and both heads are cracked and show signs of overheating, Anyone out there have 2 heads i could get or know where to look. CAST # ON HEADS ARE A21003. Thanks, Fred

 
Back to top
Jim B.
Guest






Report to Moderator
PostPosted: Mon May 21, 2007 6:38 pm    Post subject: Re: 830 cracked heads Reply to specific post Reply with quote
Do you need... Gas, Diesel or LP heads?

 
Back to top
Fred Eagerton Jr.
Guest






Report to Moderator
PostPosted: Tue May 22, 2007 3:41 am    Post subject: Re: 830 cracked heads Reply to specific post Reply with quote
It is a 301D diesel engine

 
Back to top
Jheitkemper
Guest






Report to Moderator
PostPosted: Wed May 23, 2007 10:20 am    Post subject: Re: 830 cracked heads Reply to specific post Reply with quote
thwere is a guy in E town Ky , that welded and reworked mine for an 800 .. Depending on how bad they are ,, You will pay BIG Bucks either way ..Best wishes , Jim

 
Back to top
Fred Eagerton Jr.
Guest






Report to Moderator
PostPosted: Wed May 23, 2007 6:38 pm    Post subject: Re: 830 cracked heads Reply to specific post Reply with quote
A man offered 2 heads off of a 930 today, the bolt holes seem to match up, but the heads are a little bit shorter. think i could use the push rods out of the 930 and if the water jackets match up, would it work, Only out of some time and a little $ enstead out of 900$ for 2 remaned heads.

 
Back to top
Eric John
Guest






Report to Moderator
PostPosted: Wed Jun 06, 2007 7:55 pm    Post subject: Re: 830 cracked heads Reply to specific post Reply with quote
The 930 case has a smaller bore. I do not believe that the heads will work.

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters