Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Case 930 Clutch Question


 
Post new topic    
View previous topic :: View next topic  
Author Message
931 Fan
Guest






Report to Moderator

PostPosted: Wed May 23, 2007 10:54 am    Post subject: Case 930 Clutch Question Reply to specific post Reply with quote

Have a 930 that the clutch pedal does not move when you step on it. Tractor was operating when this developed. Another family member was running it, tried to shift gears on hillside, it is the standard 8 speed trans. Tractor will still move, just devil of a time getting in gear.
Any thoughts on identifying problem, short of splitting tractor?

 
Back to top
dboll
Guest






Report to Moderator

PostPosted: Wed May 23, 2007 11:07 am    Post subject: Re: Case 930 Clutch Question Reply to specific post Reply with quote

not that it could be your problem (or maybe is) but I have seen the tube that the throwout brg. rides on come out of the front of the trans. and cause problems like clutch not disengaging properly, something to check if you split it.

 
Back to top
PamND
Guest






Report to Moderator

PostPosted: Wed May 23, 2007 5:12 pm    Post subject: Re: Case 930 Clutch Question Reply to specific post Reply with quote

On our 932 8 speed there is an inspection plate which allows us to look at the pressure plate/release bearing/yoke. This should allow you to see if yoke is trying to move when someone is pressing on the clutch. One assumption here is that the clutch peddle will move if you disconnect the linkage. Our inspection plate is to the back of the starter.

PaM

 

Back to top
bradley martin
Guest






Report to Moderator

PostPosted: Thu May 24, 2007 12:55 am    Post subject: Re: Case 930 Clutch Question Reply to specific post Reply with quote

In all likelihood, you are going to have to split the tractor. As Pam SD stated, there is the inspection cover where you grease the throw out bearing that might allow you to see what has happened buteven if you can see it you will have to split inorder to repair.

 
Back to top
Bob/wis
Guest






Report to Moderator

PostPosted: Thu May 24, 2007 1:22 pm    Post subject: Re: Case 930 Clutch Question Reply to specific post Reply with quote

First like was stated, disconnect the clutch pedal. Then see if it moves. I have had them freeze in place. Then if it does then remove the inspection cover reconnect the linkage and contunie to check things.
Bob

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters