Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1010 John Deere Crawler


 
Post new topic    
View previous topic :: View next topic  
Author Message
Rob03
Regular


Joined: 04 Jul 2005
Posts: 23


Report to Moderator

PostPosted: Sun Apr 07, 2019 5:32 am    Post subject: 1010 John Deere Crawler Reply to specific post Reply with quote

I'm working on a 1010 crawler. Just finished putting steering clutches and brake bands in. Pulled up the floor plates to adjust the brake rods and found the return spring for the petal was unhooked. My question is where does the spring hook to on the crawler itself. I looked through my manuals for some kind of information or a picture and can't find anything. Could someone please help me on this.
Thanks, Robbie
 
Back to top
View user's profile
Harold Hubbard
Long Time User


Joined: 22 Mar 2009
Posts: 631


Report to Moderator

PostPosted: Sun Apr 07, 2019 9:11 am    Post subject: Re: 1010 John Deere Crawler Reply to specific post Reply with quote

There is a lug on the bottom of the floor plate , with a hole beside it. Bolt the plate back on, and reach through the hole with a pry bar and reattach the spring. It is a little bit tricky, and don't get your fingers into it.
 
Back to top
View user's profile
Rob03
Regular


Joined: 04 Jul 2005
Posts: 23


Report to Moderator

PostPosted: Sun Apr 07, 2019 9:52 am    Post subject: Re: 1010 John Deere Crawler Reply to specific post Reply with quote

Thank you very much, never thought to look at the floor plate.
 
Back to top
View user's profile
sms
Tractor Guru


Joined: 13 Aug 2004
Posts: 6973
Location: nys catskill mts

Report to Moderator

PostPosted: Sun Apr 07, 2019 11:16 am    Post subject: Re: 1010 John Deere Crawler Reply to specific post Reply with quote

I think I have attached the spring to the floor plate as I put the plate in so you don't have to reach through the hole.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters