Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Farmall A lift

Post new topic    
View previous topic :: View next topic  
Author Message
New User

Joined: 06 Jun 2017
Posts: 18

Report to Moderator

PostPosted: Thu May 16, 2019 3:30 pm    Post subject: Farmall A lift Reply to specific post Reply with quote

Hello! Not long after I bought my AI I found a gentleman selling cultivator. He had a pile which he said contained two sets of cultivator and other parts. The cultivator that I wanted is a hand lift. One lever adjusts the left side and the other lifts everything front and back. I also got most of a liftall system. Once I am sure that I have picked out all the parts for the cultivator I want to keep, I will sell the other. I will post in classifieds. My question should I keep the liftall stuff for my tractor? I don't know that I would use it. Just thinking down the road it might make the tractor more desirable. The rear lift is heavier duty than what I put on the tractor. I do like that. Thanks in advance. Bruce
Back to top
View user's profile
1946 BN IHC

Joined: 28 May 2013
Posts: 361

Report to Moderator

PostPosted: Fri May 17, 2019 3:29 am    Post subject: Re: Farmall A lift Reply to specific post Reply with quote

Bruce If all the parts are there and in working order install it use it. Is it a pneumatic type. If so open the cylinder soak the leather ring in light oil for several days and re assemble. this will soften and re set the leathers causing them to perform better.

Back to top
View user's profile
New User

Joined: 23 Mar 2016
Posts: 19

Report to Moderator

PostPosted: Sat May 18, 2019 6:03 pm    Post subject: Re: Farmall A lift Reply to specific post Reply with quote

by most of a lift all system, do you mean you have the part that goes on the exhaust pipe, the valve for raising and lowering the lift and the cylinder. if you have the part that goes on the exhaust pipe by all means keep it, the other parts you can still find, aka gene bender. every time I pull the lever to raise the plow on my b i'm still amazed at the engineering that went into that setup
Back to top
View user's profile
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

Jump to:  

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters