Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1966 Ford 2000 3 cyl diesel exhaust stack info


 
Post new topic    
View previous topic :: View next topic  
Author Message
Bart CA
Regular


Joined: 22 Aug 2008
Posts: 165


Report to Moderator

PostPosted: Tue Oct 01, 2019 10:30 am    Post subject: 1966 Ford 2000 3 cyl diesel exhaust stack info Reply to specific post Reply with quote

I replaced exhaust manifold extention pipe and muffler
Once installed the muffler to pipe clamp has to be installed
under the hood is it the original configuration ?

The new manifolsd is aftermarket does the extention pipe supposed to fit snug
in the manifold (kind of taper) there is an exhaut leak there.Any way to
seal it ?

Thank you in advance

Bart
 
Back to top
View user's profile
shaun wallace
Tractor Guru


Joined: 11 May 2008
Posts: 3600


Report to Moderator

PostPosted: Tue Oct 01, 2019 12:46 pm    Post subject: Re: 1966 Ford 2000 3 cyl diesel exhaust stack info Reply to specific post Reply with quote

Yes, muffler clamp went under hood. The extension should fit snug in manifold. Should be notch in manifold with matching tab on pipe that line up to keep from turning.
 
Back to top
View user's profile
Bart CA
Regular


Joined: 22 Aug 2008
Posts: 165


Report to Moderator

PostPosted: Tue Oct 01, 2019 4:53 pm    Post subject: Re: 1966 Ford 2000 3 cyl diesel exhaust stack info Reply to specific post Reply with quote

Thank you Shaun for your reply greatly appreciated.

I cannot compare to the manifold i removed because the previous owner welded a steel pipe
on it and the weld failed.

There is a notch in the manifold and a tab in the pipe but the pipe has little loose
and there is an exhaust leak. It is a new after market manifold which have few defects
I think the dimentions are little different compared to the original.
I will try to find some heat resistant packing to put under the bell shaped part
of the pipe to stop leaks.

Thanks again !!!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters