Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

800 series ford


 
Post new topic    
View previous topic :: View next topic  
Author Message
Elton Fancher
Long Time User


Joined: 29 Nov 2007
Posts: 1162


Report to Moderator

PostPosted: Sat Nov 23, 2019 8:23 pm    Post subject: 800 series ford Reply to specific post Reply with quote

Was working on 800 series tractor with loader. Put on head gasket, all that is great, runs good. Loader is Ford with reservoir in frame. Front pump. Problem is the speed of lift and lower. So fast it is scary and hard to control. Any way I could slow it down?
 
Back to top
View user's profile
Bob
Tractor Guru


Joined: 03 Jan 1998
Posts: 56116


Report to Moderator

PostPosted: Sat Nov 23, 2019 10:42 pm    Post subject: Re: 800 series ford Reply to specific post Reply with quote

Most likely, you can learn to "feather" the lever to control the speed.
 
Back to top
View user's profile
Off Road SHO
Regular


Joined: 09 Jun 2009
Posts: 124


Report to Moderator

PostPosted: Sun Nov 24, 2019 3:04 am    Post subject: Re: 800 series ford Reply to specific post Reply with quote

CVPost-elton fancher wrote:
(quoted from post at 05:23:53 11/24/19) Was working on 800 series tractor with loader. Put on head gasket, all that is great, runs good. Loader is Ford with reservoir in frame. Front pump. Problem is the speed of lift and lower. So fast it is scary and hard to control. Any way I could slow it down?


Sure. Put on a longer lever. Or reduce the diameter of the hydraulic hoses.

Tom
 
Back to top
View user's profile
RobCons
Long Time User


Joined: 08 Jan 2014
Posts: 1136
Location: Central Alabama

Report to Moderator

PostPosted: Sun Nov 24, 2019 5:05 am    Post subject: Re: 800 series ford Reply to specific post Reply with quote

Restricted orifice adapters are available that just screw inline. I put a set on a Massey Ferguson a couple years ago with good results. Some people dont like them. I got mine at TSC and drilled the hole out a little bigger.
 
Back to top
View user's profile
Elton Fancher
Long Time User


Joined: 29 Nov 2007
Posts: 1162


Report to Moderator

PostPosted: Sun Nov 24, 2019 5:27 am    Post subject: Re: 800 series ford Reply to specific post Reply with quote

Thanks, this thing so fast its dangerous and I cannot control it. It shakes the whole tractor when you lift and stop. I will check out the smaller orifice first.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters