Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Fenders


 
Post new topic    
View previous topic :: View next topic  
Author Message
jhncp
Regular


Joined: 22 May 2019
Posts: 258


Report to Moderator

PostPosted: Sun Jan 05, 2020 4:23 pm    Post subject: Fenders Reply to specific post Reply with quote

I'm a Farmall guy in this place I don't belong, but I bought a M with SC Case fenders. Are these fenders only for a SC case?



 
Back to top
View user's profile
tomturkey
Tractor Expert


Joined: 21 Jul 2010
Posts: 2639


Report to Moderator

PostPosted: Sun Jan 05, 2020 4:47 pm    Post subject: Re: Fenders Reply to specific post Reply with quote

I can understand why a person might put Case SC fenders on a Farmall. The fenders on H's and M's were not really fenders they were wheel shields. To keep you from putting your hand over against a moving wheel. As far as mud sling they were better than nothing, but just a little. imho gobble
 
Back to top
View user's profile
Nedd
Long Time User


Joined: 25 Oct 2001
Posts: 820


Report to Moderator

PostPosted: Sun Jan 05, 2020 6:17 pm    Post subject: Re: Fenders Reply to specific post Reply with quote

Depends Smooth curved fenders were only sc and dc. Ones with rib supports would work on other later models. 400/700/800/730/830
 
Back to top
View user's profile
jhncp
Regular


Joined: 22 May 2019
Posts: 258


Report to Moderator

PostPosted: Mon Jan 06, 2020 8:00 am    Post subject: Re: Fenders Reply to specific post Reply with quote



 
Back to top
View user's profile
rfdmn
Regular


Joined: 13 Apr 2015
Posts: 209


Report to Moderator

PostPosted: Mon Jan 06, 2020 3:15 pm    Post subject: Re: Fenders Reply to specific post Reply with quote

CVPost-jhncp wrote:
(quoted from post at 09:00:52 01/06/20)
<img src="/cvphotos/cvphoto1484.jpg">
Are those cans near the axle clamp part of the instillation?
 
Back to top
View user's profile
jhncp
Regular


Joined: 22 May 2019
Posts: 258


Report to Moderator

PostPosted: Tue Jan 07, 2020 5:23 am    Post subject: Re: Fenders Reply to specific post Reply with quote

They are for assisting in the installation
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters