Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

51 cub front pulley


 
Post new topic    
View previous topic :: View next topic  
Author Message
boler76
Long Time User


Joined: 07 Apr 2005
Posts: 628


Report to Moderator

PostPosted: Fri Jan 17, 2020 5:03 am    Post subject: 51 cub front pulley Reply to specific post Reply with quote

if I heat the pulley to help with installing it, will the ID get bigger or will the expansion make it smaller and harder to install?
 
Back to top
View user's profile
Phil Tibbetts
Tractor Expert


Joined: 23 Jul 2004
Posts: 2651
Location: Old Town, Maine

Report to Moderator

PostPosted: Fri Jan 17, 2020 5:55 am    Post subject: Re: 51 cub front pulley Reply to specific post Reply with quote

If you heat the whole pulley it will get bigger. Ve careful if you do this because if you get it half way on and it sticks you will have a tough time getting it off again.
 
Back to top
View user's profile
glennster
Tractor Guru


Joined: 14 Aug 2007
Posts: 13124
Location: illinois

Report to Moderator

PostPosted: Fri Jan 17, 2020 6:03 am    Post subject: Re: 51 cub front pulley Reply to specific post Reply with quote

when i installed the pulley on my cub, i heated it in a deep fryer like a presto fry daddy. it will get it up to about 350 degrees or so.
 
Back to top
View user's profile
boler76
Long Time User


Joined: 07 Apr 2005
Posts: 628


Report to Moderator

PostPosted: Fri Jan 17, 2020 6:26 am    Post subject: Re: 51 cub front pulley Reply to specific post Reply with quote

and what does the seal think of a hot pully hub?
 
Back to top
View user's profile
ih560
Long Time User


Joined: 27 Sep 2007
Posts: 937


Report to Moderator

PostPosted: Fri Jan 17, 2020 7:06 am    Post subject: Re: 51 cub front pulley Reply to specific post Reply with quote

I've never needed heat to install them, just used a threaded rod with a plate and nut to draw it in.
 
Back to top
View user's profile
DeltaRed
Tractor Guru


Joined: 25 Feb 2010
Posts: 16248
Location: Delta,colorado

Report to Moderator

PostPosted: Fri Jan 17, 2020 7:12 am    Post subject: Re: 51 cub front pulley Reply to specific post Reply with quote

I just draw em on with a bolt. Just be sure the bore and shaft are clean. Maybe even use some light oil. use a bit of emery cloth if needed.Dont ever remember needing heat.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters