Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1850 Diesel Hydra-Power


 
Post new topic    
View previous topic :: View next topic  
Author Message
DG 3
Regular


Joined: 01 Mar 2020
Posts: 27


Report to Moderator

PostPosted: Fri Mar 27, 2020 9:42 am    Post subject: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

I am thinking about buying this tractor. I have been told that when you shift down to low, it stops then takes off. I don't have splitting stands. What would it
cost to get that fixed at a Dealer? Ballpark figure? Thanks in advance!
 
Back to top
View user's profile
J. Schwiebert
Tractor Guru


Joined: 27 Sep 2013
Posts: 4920


Report to Moderator

PostPosted: Fri Mar 27, 2020 10:18 am    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

The sprag clutch is wore out. You don't split the tractor to do that. You lift the engine out and remove the hydra power from the engine.
 
Back to top
View user's profile
RCP
Tractor Expert


Joined: 24 Feb 2000
Posts: 1641


Report to Moderator

PostPosted: Fri Mar 27, 2020 11:16 am    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

The parts will cost $800 to $1200, labor around $300 if you pull the hydrapower yourself.


Rich
 
Back to top
View user's profile
DG 3
Regular


Joined: 01 Mar 2020
Posts: 27


Report to Moderator

PostPosted: Fri Mar 27, 2020 12:43 pm    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

Thanks for the replies. I think I read somewhere you can do away with Hydra-Power? Or weld it together?
 
Back to top
View user's profile
ziffel
Regular


Joined: 10 Jan 2019
Posts: 135


Report to Moderator

PostPosted: Fri Mar 27, 2020 12:51 pm    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

It can be eliminated. Many of them were built without them. You need an "Eliminator Kit" The parts needed to do that can sometimes be found in salvage yards. I have replaced many Hydra-Power units with Straight shafts. I have a complete list of the necessary parts with numbers. Send me an email at arnie@yousq.net if you need a copy. Arnie
 
Back to top
View user's profile
tom upton
Regular


Joined: 14 Jan 2005
Posts: 484


Report to Moderator

PostPosted: Fri Mar 27, 2020 1:11 pm    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

Hydra powers should be relatively easy to come by. heck u might get lucky and buy a whole parts tractor cheaper than rebuilding one. In my opinion if you are going to use the tractor for much you will regret deleting it. I have a working unit I would sell for $500 if you pick it up. I am in Ontario Canada bout 100 mile north east of T.O.
 
Back to top
View user's profile
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 42235


Report to Moderator

PostPosted: Fri Mar 27, 2020 2:05 pm    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

I don't know that it'd stop me from buying it. Mine has been that way for years. I just leave it in direct,no problem.
 
Back to top
View user's profile
DG 3
Regular


Joined: 01 Mar 2020
Posts: 27


Report to Moderator

PostPosted: Fri Mar 27, 2020 2:50 pm    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

Thanks for that info. Growing up my family all had Farmalls. Mostly 806's and most of them were the same way. We just left the torque forward, no problem. I didn't know if you could drive a hydra-power like that.
 
Back to top
View user's profile
RCP
Tractor Expert


Joined: 24 Feb 2000
Posts: 1641


Report to Moderator

PostPosted: Fri Mar 27, 2020 3:14 pm    Post subject: Re: 1850 Diesel Hydra-Power Reply to specific post Reply with quote

An add on this site for a straight shaft.

Contact: Steve Located in: Norway, IA, USA *
For Sale: Hydra-Power or Over-Under delete from an Oliver 1850 gas tractor. Should fit others. Condition: Good Price: 300
Phone: 3197213066

If the sprague is bad, I would wonder how long the direct drive clutch pack is going to hold and sometimes like a Farmall they are hard to shift when in direct.

Rich
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters