Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Yo Royse


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ed Douglas
Long Time User


Joined: 31 Jan 2011
Posts: 946


Report to Moderator

PostPosted: Mon Apr 06, 2020 11:44 am    Post subject: Yo Royse Reply to specific post Reply with quote

Wanna shot at rebuilding this one??...Lmao!
 
Back to top
View user's profile
Ed Douglas
Long Time User


Joined: 31 Jan 2011
Posts: 946


Report to Moderator

PostPosted: Mon Apr 06, 2020 7:22 pm    Post subject: Re: Yo Royse Reply to specific post Reply with quote

Might help if I attached the picture




 
Back to top
View user's profile
duey
Tractor Expert


Joined: 09 May 2001
Posts: 1870


Report to Moderator

PostPosted: Mon Apr 06, 2020 7:35 pm    Post subject: Re: Yo Royse Reply to specific post Reply with quote

That should truly Warm The Hearts of the "patina' lovers...... sheesh!!
 
Back to top
View user's profile
grandpa Love
Tractor Guru


Joined: 26 May 2016
Posts: 7457


Report to Moderator

PostPosted: Tue Apr 07, 2020 4:50 am    Post subject: Re: Yo Royse Reply to specific post Reply with quote

Some one gave me a carb off a Farmall A that looked like that. Been soaking in a gallon of carb cleaner for 3 months. Some parts still won't move.
 
Back to top
View user's profile
teddy52food
Tractor Guru


Joined: 05 Mar 2006
Posts: 9630


Report to Moderator

PostPosted: Tue Apr 07, 2020 6:16 am    Post subject: Re: Yo Royse Reply to specific post Reply with quote

I had one like that & it was cast iron so I boiled it in lye water 3 times. Rinsed & blew it out each time. along with using tip cleaners. When on the engine I could idle it down to where the impulse on the mag was snapping & it continued to run that way.
 
Back to top
View user's profile
Royse
Tractor Guru


Joined: 17 Jan 2011
Posts: 17678
Location: Ionia County Michigan

Report to Moderator

PostPosted: Wed Apr 08, 2020 6:54 pm    Post subject: Re: Yo Royse Reply to specific post Reply with quote

Looks salvageable. :)
I've done quite a few similar to that.
This one from a Farmall. Nothing moved freely.






 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters