Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Impatiently waiting


 
Post new topic    
View previous topic :: View next topic  
Author Message
VicS
Tractor Guru


Joined: 12 Mar 2010
Posts: 5116


Report to Moderator

PostPosted: Wed Mar 25, 2020 2:10 pm    Post subject: Impatiently waiting Reply to specific post Reply with quote

Think they are good to go. D17 Needs
painting but that is this winter, I hope.
Ran good at Russellville Ky. But needed a
better driver. Maybe It'll shed 50 more
pounds by time this Virus is whipped.

 
Back to top
View user's profile
4010 puller
Tractor Expert


Joined: 27 Sep 2004
Posts: 1546


Report to Moderator

PostPosted: Sat Apr 04, 2020 12:15 pm    Post subject: Re: Impatiently waiting Reply to specific post Reply with quote

How is the d17 holding up? Plenty of power? How many rpm?
 
Back to top
View user's profile
VicS
Tractor Guru


Joined: 12 Mar 2010
Posts: 5116


Report to Moderator

PostPosted: Sat Apr 04, 2020 7:31 pm    Post subject: Re: Impatiently waiting Reply to specific post Reply with quote

So far so good. It has made it down the track 6 times. Didn't have any trouble. Just have pump set on 3000 rpm. And 250 plus hp. There are a lot of mean tractors out there. I haven't got the balance yet. I was running constantly heavy on the front. Think I should have not pulled it open at the end. 6 and 8 mph. Classes. My buddy won and he just helt his throttle about 3/4 and let it pull down at the end. It weighs 4040 with me and 2 big batteries. Like to get below 4000. And I can eventually. How are your Project's coming along?
 
Back to top
View user's profile
4010 puller
Tractor Expert


Joined: 27 Sep 2004
Posts: 1546


Report to Moderator

PostPosted: Sun Apr 05, 2020 10:51 am    Post subject: Re: Impatiently waiting Reply to specific post Reply with quote

I?ve put a set of cuts on the oliver and a redone injection pump to get some more power for 6 mph class.patiently waiting, may not get to pull much this year. How close do you get to ohio to pull? You ever going to try harrisburg out?
 
Back to top
View user's profile
VicS
Tractor Guru


Joined: 12 Mar 2010
Posts: 5116


Report to Moderator

PostPosted: Sun Apr 05, 2020 5:42 pm    Post subject: Re: Impatiently waiting Reply to specific post Reply with quote

Yes would like to go to Harrisburg again. I went the year it was called off because the fumes got so bad. But I got to pull since I was First and second class of 5 mph. Some how the little 435 made a full pull in the 3500 along with a 350U He won the pull off. But I won the 4000. And it powered out! Sometimes its your day.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters