Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

WD 45 transmission


 
Post new topic    
View previous topic :: View next topic  
Author Message
Mike in Ohio
Regular


Joined: 02 Feb 2002
Posts: 429


Report to Moderator

PostPosted: Sun Aug 09, 2020 12:52 pm    Post subject: WD 45 transmission Reply to specific post Reply with quote

I am putting the main shaft back together after replacing the double bearing. The manual mentions pins in the collars the gears ride on. There were no pins when I took it apart, what is purpose of them, and where can I get them? How big are they?

Thanks for the help,
Mike
 
Back to top
View user's profile
DrAllis
Long Time User


Joined: 18 Jan 2015
Posts: 1432


Report to Moderator

PostPosted: Sun Aug 09, 2020 2:11 pm    Post subject: Re: WD 45 transmission Reply to specific post Reply with quote

Each of the three "bushings" the top shaft gears ride on must have a pin in them to keep the bushing from spinning on the mainshaft. 70225948 is the part number from an AGCO dealership. Use grease to hold them in place when assembling.
 
Back to top
View user's profile
Lynn Marshall
New User


Joined: 04 Jul 2020
Posts: 2


Report to Moderator

PostPosted: Sun Aug 09, 2020 6:43 pm    Post subject: Re: WD 45 transmission Reply to specific post Reply with quote

Make sure that they're not laying in the bottom of the transmission case. They are easy to lose.
 
Back to top
View user's profile
Mike in Ohio
Regular


Joined: 02 Feb 2002
Posts: 429


Report to Moderator

PostPosted: Sun Aug 09, 2020 8:22 pm    Post subject: Re: WD 45 transmission Reply to specific post Reply with quote

Thanks a lot guys I think I found one during disassembly, I thought it was part of the bearing that came apart. I need 4 right?
 
Back to top
View user's profile
DrAllis
Long Time User


Joined: 18 Jan 2015
Posts: 1432


Report to Moderator

PostPosted: Mon Aug 10, 2020 3:17 am    Post subject: Re: WD 45 transmission Reply to specific post Reply with quote

One for each bushing....three.
 
Back to top
View user's profile
Mike in Ohio
Regular


Joined: 02 Feb 2002
Posts: 429


Report to Moderator

PostPosted: Thu Aug 13, 2020 3:30 pm    Post subject: Re: WD 45 transmission Reply to specific post Reply with quote

DrAllis wrote:
(quoted from post at 15:11:37 08/09/20) Each of the three "bushings" the top shaft gears ride on must have a pin in them to keep the bushing from spinning on the mainshaft. 70225948 is the part number from an AGCO dealership. Use grease to hold them in place when assembling.



Thanks again. They came in todays mail
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters