Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Looking for help


 
Post new topic    
View previous topic :: View next topic  
Author Message
gslehew
New User


Joined: 26 Sep 2020
Posts: 2


Report to Moderator

PostPosted: Sat Sep 26, 2020 10:13 pm    Post subject: Looking for help Reply to specific post Reply with quote

I recently got my grandpas ferguson tractor. Serial # is TO-51069. I was told it was a 1952 but researching the number i dont find it in 1952. Also Im not sure if it is a 20 or 30. Can anyone help with information? Thanks Greg
 
Back to top
View user's profile
wjytexas
Tractor Guru


Joined: 01 Sep 2013
Posts: 4014


Report to Moderator

PostPosted: Sun Sep 27, 2020 4:02 am    Post subject: Re: Looking for help Reply to specific post Reply with quote

on the engine block it will have Z 120 or Z 129. z 120 is a to 20, 129 a to 30. Serial number indicates t0 20
 
Back to top
View user's profile
Tom H.
Long Time User


Joined: 24 Feb 2008
Posts: 956


Report to Moderator

PostPosted: Sun Sep 27, 2020 4:52 am    Post subject: Re: Looking for help Reply to specific post Reply with quote

Looks like a late 1951 TO20. The engine block, as stated, should say Continental Z120-. Let us know what else you need help with.
 
Back to top
View user's profile
miner09
Tractor Expert


Joined: 02 Dec 2009
Posts: 2972


Report to Moderator

PostPosted: Sun Sep 27, 2020 6:41 am    Post subject: Re: Looking for help Reply to specific post Reply with quote

On a 30 it will have a air intake dome with screen on right side dash. A
20 doesn't have it. One easy way to know.
 
Back to top
View user's profile
Steve@Advance
Tractor Guru


Joined: 12 Nov 2013
Posts: 18350


Report to Moderator

PostPosted: Sun Sep 27, 2020 6:44 am    Post subject: Re: Looking for help Reply to specific post Reply with quote

Welcome gslehew!

Looking at the dash, a TO20 is basically flat.

A TO30 has a raised bezel around the ign switch, and the air intake through the right face of the dash.
 
Back to top
View user's profile
gslehew
New User


Joined: 26 Sep 2020
Posts: 2


Report to Moderator

PostPosted: Sun Sep 27, 2020 11:17 am    Post subject: Re: Looking for help Reply to specific post Reply with quote

Flat dash no air intake. Plate on engine block is petty wire. Trying to clean it up. Thanks for the help guys. Much appreciated.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters