Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

202 clutch replacement tractor split


 
Post new topic    
View previous topic :: View next topic  
Author Message
jesse CA
Regular


Joined: 30 Nov 2012
Posts: 69


Report to Moderator

PostPosted: Thu Oct 22, 2020 6:17 am    Post subject: 202 clutch replacement tractor split Reply to specific post Reply with quote

Hello all
Might Anyone share their experience with splitting their 202 with a loader on it? How was it? How did you go about it? My primary clutch is beginning to slip a bit. I'm thinking about putting together that rail fixture to hopefully make the process go a bit easier and safer? supporting the loader frame is a concern as well?
 
Back to top
View user's profile
jesse CA
Regular


Joined: 30 Nov 2012
Posts: 69


Report to Moderator

PostPosted: Thu Oct 22, 2020 6:26 am    Post subject: Re: 202 clutch replacement tractor split Reply to specific post Reply with quote

Also dealing with all the hydraulic fluid?
 
Back to top
View user's profile
Steve@Advance
Tractor Guru


Joined: 12 Nov 2013
Posts: 18324


Report to Moderator

PostPosted: Thu Oct 22, 2020 9:29 am    Post subject: Re: 202 clutch replacement tractor split Reply to specific post Reply with quote

I just can't envision it happening with the loader in place, but never tried. Usually trying to do something like that turns into more work than just getting it out of the way.

Hopefully you have a good slab to work on.

My preferred method (with the loader gone) is to crib under the transmission, take the front end apart, down to manageable size pieces, lift the engine away with a cherry picker, A frame, trolley hoist, another tractor, some way to move it back to disengage the input shaft.

Going back you need all the control you can get, don't want to let the weight of the engine hang on the new clutch. If it is a dual clutch, you MUST use an alignment shaft. The engine has to mate back up with the transmission without excessive force.

The reason I say disassemble the front, chances are if it's had loader use for any time, and the front end hasn't been gone through, it will need attention while you are there.
 
Back to top
View user's profile
Bruce(OR)
Tractor Expert


Joined: 10 Apr 2007
Posts: 3434


Report to Moderator

PostPosted: Thu Oct 22, 2020 9:40 am    Post subject: Re: 202 clutch replacement tractor split Reply to specific post Reply with quote

What, why, where? Isn't FEL a contained system?
 
Back to top
View user's profile
scoobieguy
Regular


Joined: 17 Aug 2018
Posts: 76


Report to Moderator

PostPosted: Sat Oct 24, 2020 5:46 am    Post subject: Re: 202 clutch replacement tractor split Reply to specific post Reply with quote


I helped a friend split a 202 with front loader but no backhoe, we never drained the oil from the loader.
We left the loader bucket bolted to the front of the tractor an it was supported by the side using his car lift, you don't need a car lift to support it just blocks would have worked, the heavy bucket is like an anchor at the front.
Then we unbolted the loader frame from from the back axle and rolled he backend "backwards approximately 2ft with a large floor jack while the engine was supported by a smaller bottle jack.
On reassembly we used long rods to align the while thing without forcing things.
The worse thing with the front loader still mounted is accessing some bolts, and the worse was the steering and column, it is surprisingly heavy and awkward to put back in and align the shift rails because of the loader assembly.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters