Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Shifter


 
Post new topic    
View previous topic :: View next topic  
Author Message
vfleak
New User


Joined: 25 Sep 2020
Posts: 9


Report to Moderator

PostPosted: Sun Oct 18, 2020 8:40 pm    Post subject: Shifter Reply to specific post Reply with quote

I am replacing the shifter on my Alis Chalmer CA got the old one out but can't get replacement lined uo its the part on the side of tractor with the forks any suggestions ?
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 13982
Location: Edon Ohio

Report to Moderator

PostPosted: Mon Oct 19, 2020 2:59 am    Post subject: Re: Shifter Reply to specific post Reply with quote

Take the side plate off. Something is out of place on the side plate. Make sure the forks are snapped in the ident balls. Then line up the gears with the forks.
 
Back to top
View user's profile
vfleak
New User


Joined: 25 Sep 2020
Posts: 9


Report to Moderator

PostPosted: Mon Oct 19, 2020 11:39 am    Post subject: Re: Shifter Reply to specific post Reply with quote

You said Make sure the forks are snapped in the ident balls what are they Thanks for your reply
 
Back to top
View user's profile
krumenacker
Regular


Joined: 17 Jun 2016
Posts: 72
Location: Upper Peninsula, MI

Report to Moderator

PostPosted: Mon Oct 19, 2020 4:52 pm    Post subject: Re: Shifter Reply to specific post Reply with quote

vfleak wrote:
(quoted from post at 21:40:15 10/18/20) I am replacing the shifter on my Alis Chalmer CA got the old one out but can't get replacement lined uo its the part on the side of tractor with the forks any suggestions ?


Was it in neutral when you pulled the shifter?

When you pull the side plate, the forks move the gears.

Detente is when they lock into place.
 
Back to top
View user's profile
krumenacker
Regular


Joined: 17 Jun 2016
Posts: 72
Location: Upper Peninsula, MI

Report to Moderator

PostPosted: Mon Oct 19, 2020 4:59 pm    Post subject: Re: Shifter Reply to specific post Reply with quote


Apologies, eyes getting bad. Ignore detente comment.
 
Back to top
View user's profile
vfleak
New User


Joined: 25 Sep 2020
Posts: 9


Report to Moderator

PostPosted: Mon Oct 19, 2020 7:28 pm    Post subject: Re: Shifter Reply to specific post Reply with quote

Thanks for you reply . I have tried at least 20 times and still not getting it to line up never one was to quit so I will keep at it
 
Back to top
View user's profile
vfleak
New User


Joined: 25 Sep 2020
Posts: 9


Report to Moderator

PostPosted: Wed Oct 21, 2020 8:30 pm    Post subject: Re: Shifter Reply to specific post Reply with quote

Thanks finally got everything lined up and is working !
 
Back to top
View user's profile
vfleak
New User


Joined: 25 Sep 2020
Posts: 9


Report to Moderator

PostPosted: Wed Oct 21, 2020 8:35 pm    Post subject: Re: Shifter Reply to specific post Reply with quote

Fork for First and Fourth gear were worn to probably half the width had another CA I bought for parts and switched out shifter plate works fine now !
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters